Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Acura Integra GSR VTEC Throttle Body Installation Instruction

This part is street legal in all 50 states for use on 1994-2001 Acura Integra GSR 1.8L Vtec.
Throttle Body Kit Contents:
1 – Throttle body to manifold gasket
1 – Fast idle thermo valve o-ring with white stripe
1 – Fast idle thermo valve o-ring with red stripe
1 – Fast idle thermo valve o-ring with green stripe
1 – MAP sensor o-ring with blue strip
1 – E.O. # fan shroud decal
[Read the rest of this entry...]

Leave a Comment

Installation instructions for Stratmosphere HyperBoost Valve

Bob and I appreciate your purchase of your HyperBoost Valve from Stratmosphere. Please read these instructions prior to installation so that you can enjoy a simple and quick installation of your new HyperBoost valve! –Pete
What’s included with your package:
• One HyperBoost diverter valve
• Two medium sized hose clamps
• One small hose clamp
• One instruction sheet (you are reading it)
[Read the rest of this entry...]

Leave a Comment

2010 Insight Body Side Molding Installation Instructions

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.

NOTE:
• Be careful not to damage the body paint finish.
• Body side moldings should only be installed if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
• These installation instructions show the left body side moldings being installed. The same procedure applies to installing the right body side moldings.

1. Using one alcohol swab, clean the area where the left body side molding will attach.
2. Align the front template to the left front door and attach the template to the door using strips of masking tape.
3. Place the left front body side molding against the template to verify the installation position on the left front door. Remove the body side molding.
4. Peel back approximately 1½ to 2 inches of adhesive backing from each adhesive tape, and tape the ends to the front surface of the body side molding. Remove the small end pieces of the adhesive backing.
5. Align the left front body side molding with the front template, and attach it to the left front door. If the vehicle has door edge film installed, align the end with the door edge film.

Download

Leave a Comment

Acura B18 Valve Spring Set Instructions

The COMP Cams® Acura/Honda B-Series VTEC valve spring set (Fig. A) utilizes dual springs on the intake side and a single spring on the exhaust side. Below are the information and diagrams to ensure correct installation.
Installation Instructions:
Dual Intake Spring
Installed Height: 60lbs at 1.375
Open Height: 220 lbs at .875
Coil Bind Height: .815
Spring Rate: 300 lbs per inch
[Read the rest of this entry...]

Leave a Comment

1996-2001 Honda Acura Integra Type R Edelbrock 65mm Throttle Body INSTALLATION INSTRUCTIONS

This part is street legal in all 50 states for use on 1996-2001 Honda Acura Integra Type R vehicles.
1. Please read through the entire instruction sheet to familiarize yourself with the installation before you begin.
2. Start the engine and check for loose connections or coolant/vacuum leaks, etc.
3. Disconnect the negative battery terminal.
4. Remove the air filter duct, all vacuum hoses, water (coolant) hoses and electrical connectors from the stock throttle body. Mark all hoses and wires to ensure that they are installed correctly on the new throttle body.
Note: Engine coolant may run from the hoses once disconnected. Plug the end of the hose temporarily.
[Read the rest of this entry...]

Leave a Comment

1993-1998 VW Golf III 2.0L 8-valve B&M Short Shift System Instructions

This B&M Short Shift System has been designed to work on most 1993-1998 VW 2.0L 8-valve models. It has been engineered to greatly reduce shift throw and improve shift feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Shift System. Installation of the B&M Short Shift System can be accomplished by anyone with minimal mechanical experience.
[Read the rest of this entry...]

Leave a Comment

2001-02 Saturn SL1 Automatic Transmissions Saturn MP6 & MP7 Overhaul

Disassembly 1. Remove line actuator cover bolts. See Fig. 53 . Carefully remove cover and connector plate. Remove line actuators by twisting line actuator as it is pulled from valve body. 2. Remove through bolts. Separate valve body and separator plate. Remove check balls. See Fig. 54 . Remove manual valve. Remove each valve assembly. Retain in proper order for reassembly. See Fig. 55 and Fig. 56 .
[Read the rest of this entry...]

Leave a Comment

Audi TT 2000-2007 Body Interior 70 – Front door trim

Front door trim, removing and installing
1 – Door trim
Remove screw cap – 5 -
Remove screw – 4 – (1x).
Unclip inner and outer connecting pieces. .
Lift door trim about 20 cm upward and remove from door.
Detach release cable for interior door handle
Disconnect electrical connectors
Clip locators – 3 – (7x) must be clipped in place when installing door trim.
[Read the rest of this entry...]

Leave a Comment

Body Badge Installation

The badges are made from layers of foil and other materials, all covered with a pliable urethane clear “lens.” They are thin, not more than 1/16 inch thick, so they are very slick and appear to have been molded right into the painted surface of the body work. In comparison, the raised stock badges and aftermarket versions look rather crude. Since the badge colors match the various car colors perfectly, the integrated appearance of the badges is all the more striking. Depending on the color of your car and the color of the badge you chose, the end result could be very subtle and sophisticated or more striking. To avoid mistakes, please read these directions fully before beginning.

Required items:
• Xenit Adhesive remover from Stoner, or 3M Adhesive Remover available from your local auto store
• Waxed dental floss
• General purpose masking tape
• Soft cotton detailing towel
• Isopropyl Alcohol and cotton balls or alcohol swabs
• Optional: aftermarket finishing/detailing spray, we use Zaino’s Z-6.

Quick Installation Instructions
The adhesive of the badges cures better when the temperature is 70º or higher. It has been reports that installation can/has been done at lower temperatures with out any problems.
1. Clean the badge and sounding areas to remove all dirt, dust, oils, etc.
2. Remove the stock badges.
3. Clean the badge location by wiping with clean towel and isopropyl alcohol.
4. Remove the backing from the S Badge and apply the adhesive side to the clean, dry surface. Use a rolling manner (from bottom to top) to prevent air bubbles. Using caution contaminate the adhesive on the back of the emblem.

Download

Leave a Comment

Fuel and exhaust systems – K-Jetronic fuel injection – 16 valve engines

The components of the K-Jetronic fuel injection system fitted to the 1.8 litre 16V engine are as shown (see illustrations). All procedures are the same as described in Part B of this Chapter except for those given in the following Sections.
2 Idle speed – adjustment
1. Run the engine to normal operating temperature, then check that all electrical components are switched off. Note that the electric cooling fan must not be running during the adjustment procedure.
[Read the rest of this entry...]

Leave a Comment