O2™ : Silicon Graphics 1600SW Flat Panel Monitor Adapter Installation Guide
Jun.25, 2008 in
Computer, Peripheral
This guide tells you how to install the Silicon Graphics 1600SW flat panel monitor adapter board in the O2 workstation. There are two classes of O2 workstations, the R5000, and the R10000. The 1600SW flat panel monitor adapter can be installed in either class of O2 workstation.
The guide is organized as follows:
• Chapter 1 describes how to install the adapter board in your O2 workstation.
• Chapter 2 describes how to adjust the flat panel timing tables and how to calibrate color for the 1600SW flat panel monitor.
• Chapter 3 provides troubleshooting information, technical specifications, and regulatory statements.
• The glossary defines many of the terms used in the manual.
[Read the rest of this entry...]
Cardiology II Panel Editorial Board Liaison Marisel Segarra-Newnham, Pharm.D., MPH, FCCP, BCPS Clinical Pharmacy Specialist, Infectious Diseases Patient Support Service Judy W.M. Cheng, Pharm.D., MPH, Veterans Affairs Medical Center FCCP, BCPS (AQ Cardiology) West Palm Beach, Florida Professor of Pharmacy Practice Clinical Assistant Professor of Pharmacy Practice Department of Pharmacy Practice University of Florida College of Pharmacy Massachusetts College of Pharmacy and Health Sciences Gainesville, Florida Clinical Pharmacist Department of Pharmacy Atrial and Ventricular Brigham and Women’s Hospital Boston, Massachusetts
Cardiology III Panel Editorial Board Liaison Anticoagulation Management in Pregnancy Judy W.M. Cheng, Pharm.D., MPH, FCCP, BCPS (AQ Cardiology) Authors Professor of Pharmacy Practice Department of Pharmacy Practice Nathan P. Clark, Pharm.D., BCPS, CACP Massachusetts College of Pharmacy and Health Sciences Clinical Pharmacy Supervisor Clinical Pharmacist Anticoagulation Service Department of Pharmacy Kaiser Permanente Colorado Brigham and Women’s Hospital Clinical Assistant Professor Boston, Massachusetts University of Colorado Denver School of Pharmacy Aurora, Colorado Mary Beth Dowd, Pharm.D., BCPS, CACP Cardiovascular Disease
OPEL 2000 1 Keep these instructions for future use. The Owner’s Manual Residential Factory Built Fireplace Operation Maintenance Installation OPEL 2000 opel/09/99 manual OPEL 2000 2 Dear Customer, The OPEL 2000 incorporates technology with elegance to give you a beautiful view of the fire without compromising on heating efficiency or environmental quality. We have designed your new OPEL 2000 to be easy to install, operate and maintain. It is in your best interest to become familiar with it. Study your manual to be sure that the installation is correct, then follow the guidelines for operation and maintenance. We at RSF ENERGY congratulate you on your choice of the OPEL 2000, and are confident that you have purchased a fireplace that is simply, the best. Sincerely, The RSF Energy Team, Septembre 1999. SAFETY FIRST 3 Do s and Don ts 3 Creosote Formation and Need for Removal GENERAL SPECIFICATIONS 3 Combustion
1.051 Structural Engineering Design Prof. Oral Buyukozturk Fall 2003 SAP 2000 Tutorial Session Notes This tutorial provides the basic steps of performing a frame analysis using SAP 2000. It is based on the design project example shown below, the complete solution of which is provided as a handout. 16@21′ 26′ 34′ 26′ 20′ 5@13′ 15′ Results of Preliminary Analysis: Slab thickness: 9 in Beam dimensions: 14”x31” Exterior columns: 14”x18” Interior columns: 16”x22” Loads: Exterior beams: LL=0.72 kips/ft DL=1.85 kips/ft Interior beams: LL=0.83 kips/ft DL=2.10 kips/ft Wind and Earthquake loads are specified in the appendix. Only earthquake loads are considered. The frame is solved in the short direction only since this direction is more critical. 1.051 Structural Engineering Design Prof. Oral Buyukozturk Fall 2003 Analysis Steps 1. Generate the frame geometry from analysis templates. Menu: File > New model from template Result Note: make sure that proper units are selected (shown
1.051 Structural Engineering Design Prof. Oral Buyukozturk Fall 2003 SAP 2000 Tutorial Session Notes This tutorial provides the basic steps of performing a frame analysis using SAP 2000. It is based on the design project example shown below, the complete solution of which is provided as a handout. 16@21′ 26′ 34′ 26′ 20′ 5@13′ 15′ Results of Preliminary Analysis: Slab thickness: 9 in Beam dimensions: 14”x31” Exterior columns: 14”x18” Interior columns: 16”x22” Loads: Exterior beams: LL=0.72 kips/ft DL=1.85 kips/ft Interior beams: LL=0.83 kips/ft DL=2.10 kips/ft Wind and Earthquake loads are specified in the appendix. Only earthquake loads are considered. The frame is solved in the short direction only since this direction is more critical. 1.051 Structural Engineering Design Prof. Oral Buyukozturk Fall 2003 Analysis Steps 1. Generate the frame geometry from analysis templates. Menu: File > New model from template Result Note: make sure that proper units are selected (shown