Free PDF Manual Guide

This Service Light & Airbag Reset Tool is an essential tool for resetting of oil service light, service warning light, service mileage, service intervals and airbag on European made vehicles like AUDI, BMW, CITROEN, M. BENZ,MINI, SAAB, SEAT, SKODA,VOLKSWAGEN, VOLVO, etc. It is light, compact and very convenient without using the OEM Scanner to do the job. Once hooked up to the vehicle Data Link Connector (DLC), it can perform the following functions:
[Read the rest of this entry...]

This Service Light & Airbag Reset Tool is an essential tool for resetting of oil service light, service warning light, service mileage, service intervals and airbag on European made vehicles like AUDI, BMW, CITROEN, M. BENZ,MINI, SAAB, SEAT, SKODA,VOLKSWAGEN, VOLVO, etc. It is light, compact and very convenient without using the OEM Scanner to do the job. Once hooked up to the vehicle Data Link Connector (DLC), it can perform the following functions: Reset of Oil Service Light Reset of Service Warning Light Setting of Oil Service Mileage Setting of Service Mileage Interval Setting of 1st Inspection Service Interval Setting of 2nd Inspection Service Interval Reset of Airbag
[Read the rest of this entry...]

After car crashed and airbag had deployed, VW-Audi airbag sensor will stay locked
(Control unit faulty or deployed) and must be replaced. Even after small accident, Airbag sensor will write into it’s internal memory an error message “crash data stored” or “computer fault” and after it need to replace the expensive sensor to a new one. With our VAG Airbag Reset Tool you can reset and repair the airbag computer in your workshop in 1 minute. No need to remove airbag sensor from the car.
[Read the rest of this entry...]

After car crashed and airbag had deployed, VW-Audi airbag sensor will stay locked (Control unit faulty or deployed) and must be replaced. Even after small accident, Airbag sensor will write into it’s internal memory an error message “crash data stored” or “computer fault” and after it need to replace the expensive sensor to a new one. With our VAG Airbag Reset Tool you can reset and repair the airbag computer in your workshop in 1 minute. No need to remove airbag sensor from the car.
[Read the rest of this entry...]

Damaged or defective wires and connectors (e.g. chaffed insulation, broken connector pins, torn crimping) in airbag firing circuits, will cause the airbag light (SRS light) to illuminate, and will set fault code “resistance too high” in airbag control module.
[Read the rest of this entry...]

Opel Airbag Reset Tool user manual http://www.dlsmelecom.com/ Opel Airbag Reseter After car crash and airbag deployment, Opel airbag sensor always stay locked (Controlunit faulty or deployed) and must be replaced. Even after small accident Airbag sensor will write in internal memory special error message “crash data stored” or “computer fault” and after you need to exchange very expensive sensor to new one. With our Opel Airbag Reset Tool you can reset and repair airbag computer in your office in 1 minute. No need to remove airbag sensorfrom the car. How Opel Airbag Reseter works: Very simple user instruction: connect this tool to Opel OBD II connector (for cars from year 1996-2002). RED button is for airbag “crash data” erase.Push this button once and wait: yellow light start to flash and after 15 second green light inform you that “crash data” is erased. Red light set ON if erasing is not
[Read the rest of this entry...]

For 2004, the Toyota RAV4 features a more robust engine, exterior and interior updates, and more standard equipment. The previous 148-hp, 2.0-liter four-cylinder has been supplanted by a 2.4-liter that makes 161 hp. The suspension and steering have been retuned accordingly. The front and rear ends both have a new look, and inside, cosmetic changes include a redesigned steering wheel, instrument panel, and center dash. Anti-lock brakes with brake assist are now standard, as are air conditioning, cruise control, steering-wheel audio controls, and power windows, door locks, and mirrors. The RAV4′s interior has more room than most mid-size station wagons: 68.3 cubic feet in the rear. The original cute-ute is available with front-wheel drive or a full-time four-wheel-drive system that operates transparently. The RAV4 is nimble, practical, good looking, and well made.
[Read the rest of this entry...]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: These installation instruction show the left fog light begin installed. The same procedure applies to installing the right fog light.

1. Make sure you have the anti-theft code for the radio, write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery. Installing the Fog Light
3. Open the hood. Loosen the battery bracket nut. Remove the radiator cover (seven clips and one bolt).
4. Remove the four clips, four bolts, and two self-tapping screws that fasten the front bumper. Remove the front bumper.
5. Using masking tape, cover the bumper around the fog light opening.
6. Using a utility knife, slowly and carefully cut out the fog light opening. Be sure to cut your lines as straight as possible, and do not damage the bumper. Remove any burrs from the edges of the fog light grille opening with a file.
7. Attach the rubber trim to the edge of the fog light opening.
8. Position the left fog light adjuster on the left fog light, and install one step screw and one 4 x 8 mm washer-screw.

Download

Part content: ignition coil and igniter, charging system, junction connector, combination meter, engine control, air injection control driver data link connector 3, engine control module. Skid control ECU with actuator suspension, camshaft timing control valve LH, Multiplex Communication System. Engine Immobilisers System.
[Read the rest of this entry...]

Installation Guide:
1. Removing factory tail light. Seat removal needed (2 alien bolts and slide it outj.Upper tail needs to be removed (4 alien bolts and gently pull up and back – remove left and right side covers first). Disconnect factory tail light harness.
2. Unscrew two screws holding bracket to upper tail. Remove bracket and swap over to new LED tail light. Take note the order of the washers. Locate and disconnect the factory signal connectors (blue and orange). Remove factory signals
[Read the rest of this entry...]