Free PDF Manual Guide

Before you start installation
Take some engine bay pictures for later reference.
Make a special drawing of all the coolant hoses going to the different parts of the stock intake, you will need this later on. The same goes for the vacuum hoses to the different parts of the intake.
Mark the electrical connectors to the MAP sensor and TPS sensor. You will need this later on.
Drain the engine coolant.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Congressman Mike Honda became a schoolteacher early in his career because he wanted to challenge young people not only to learn but to view every student as being on an equal playing field. He became a congressman in large part because he wanted national policy-makers to view all Americans on an equal playing field.

This was the message Rep. Honda gave to employees Thursday as the keynote speaker concluding the Laboratory’s Asian Pacific American Heritage Month festivities.
[Read the rest of this entry...]

When choosing a mounting location remember: Leave at least 3 inches of clearance for the cable. The PhatBox should be mounted parallel or perpendicular to the floor of the car. Don’t mount near wiring or fuel lines. Leave the front of the PhatBox unobstructed for easy insertion of and removal of the cartridge. The unit should be mounted to a hard stable surface, such as particle board or sheet metal.
[Read the rest of this entry...]

Recently I purchased a new Honda CIVIC Hybrid. My other vehicle is a 1994 S10 Electricar pick-up truck that hadn’t been on the road for over 2 years when I got it and now I drive it every week. Why would an EAA EV driver purchase this kind of car? How is it compatible with electric vehicles?
[Read the rest of this entry...]

SECTION 1: PRE-INSTALLATION PRECAUTIONS:
Step 1: Remove the negative battery cable. Before removing the battery cable, verify that you have the “anti theft” radio code. It is usually located in your owner’s manual or on the side of the glove compartment. If you cannot find the radio code, take your car to your local Honda dealer so that they can retrieve the code through the Honda computer network.
SECTION 2: INJECTOR INSTALLATION
Step 2: Remove the plastic cosmetic cover from the intake manifold.
Step 3: Remove the five 12mm headed bolts/nuts that hold the plastic upper intake manifold to the aluminum lower manifold. Be careful when these two manifolds are not bolted together. Errant bolts/nuts or debris could fall into the intake manifold and cause severe engine damage. It is recommended that you cover the lower intake runners with protective tape or a shop towel.
[Read the rest of this entry...]

1. All machine work may be accomplished on a CNC vertical mill capable of 3-4 axis interpolation with sufficient height to accommodate block height. The bore center distances must be maintained within ±.0005 for sleeve installation to seal properly. (see block specification sheets for dimensions)(See #12 for bore center specs.)
2. All machining must produce a good surface finish and the tolerances must be maintained to assure a quality fit and sleeve seal.
3. Block must be square and perpendicular to machine head. Fixturing should be on main journals provided they are not cracked or [Read the rest of this entry...]

Dave started his bike career restoring an early CB750. Buying bits from a breaker led to him buying job lots and before he knew it he was dealing in new and used Honda parts in London. That was back in the mid-80′s, just when older Japanese bikes were beginning to earn serious credibility as significant classic machines.
[Read the rest of this entry...]

This interface connects an iPod directly to your Honda or ACURA audio system. lt’s on-board software translates commands from your Honda CD changer controls into commands that the iPod understands. This interface enables the iPod to take the place of a Honda CD changer and provides the following benefits:
Directs the iPod’s audio output to Honda vehicle audio system for optimal sound quality playback. Controls the iPod via vehicle’s radio and steering wheel controls. r Charges the iPod’s internal battery, and charging stops automatically at one hour after iPod is paused. iPod will go to SLEEP mode after charging
[Read the rest of this entry...]