Free PDF Manual Guide

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Whether you buy or lease a Honda vehicle, Honda Financial Services can assist you with the process. Please ask your dealer which lease or purchase plan best suits your needs. Want your own look? Ask your dealer about Honda Genuine Accessories.They’re designed, engineered and tested to meet the same exacting standards as your new vehicle – and a high-quality way to make your new Honda a reflection of your one-of-a-kind personality.
[Read the rest of this entry...]

This Dash Mount is designed for: Location: Tools Required: Monteringsanvisning Mounting Instruction Do not use force when working with plastic components. Use extreme care not to scratch the interior of the vehicle. MTU may not be held liable for any damage to a vehicle connected to the installation. Correct direction of the rose pattern. Steg 1: Under askebegret i bunnen av midtkonsollet finner du en torx-20 skrue som du skrur ut. Skyv så hele askebeger enheten, med panel, rett ned. Steg 2: Under varneapparat-panelet funner du 2 torx-20 skruer som skrus ut. Grip tak i hele panelet og trekk det rett ut. Dette er festet med 3 klips i overkant og det midterste kan trenge litt hjelp ifra et bendeverktøy. Steg 3: Ta av beskyttelses tapen på Dash Mounten og huk den over panelets høyre øvre kant. Trekk godt inn. Steg 4: Monter det hele tilbake på plass i motsatt
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Do not exceed 68 MPH 110 km h in the 2 position 1 Low gear Use this position when climbing steep hills slowly or slow driving through deep snow sand or mud or for maximum engine braking on steep downhill grades Do not shift into the 1 position at speeds above 34 MPH 55 km h Do not exceed 34 MPH 55 km h in the 1 position climbing a gentle slope you may feel uncomfortable shift shocks as the transmission shifts between third gear and overdrive repeatedly In this case set the OVERDRIVE switch to the OFF position The O D OFF indicator light in the instrument panel comes on at this time When driving conditions change reset the OVERDRIVE switch to the ON position Remember not to drive at high speeds for extended periods of time with the OVERDRIVE switch in the OFF position This reduces fuel economy Accelerator downshift in D position For rapid passing or hill climbing while driving fully depress the accelerator pedal to the floor This shifts the transmission down into third gear second gear or first gear depending on vehicle speed ASD0613 OVERDRIVE SWITCH Type A ON For normal driving push the [Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Turn the ignition key to the OFF position and secure the steering wheel in a straight ahead position with a rope or similar device Never place the ignition key in the LOCK position This will result in damage to the steering lock mechanism Move the gearshift lever to the N Neutral position When towing with the rear wheels on the ground release the parking brake.
[Read the rest of this entry...]

The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some models and years still pending) and come with complete instructions for ease of installation.
[Read the rest of this entry...]

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
[Read the rest of this entry...]

Remove the bezel that surrounds the climate control and extends behind the transmission shifter. To do this, grasp the bezel behind the shifter and release the first clip. In the upper-right corner of the bezel, use the Dash Trim tool to work loose the remaining ten (10) clips that hold the bezel in place. Note: On vehicles without the navigation system and/or with the DVD, the climate controls will come off with the bezel. Note: On vehicles that have the navigation system, disconnect the emergency light switch connector, and interior lighting switch. Apply the emergency brake and turn the ignition to the on position. Place the transmission shifter into the neutral position. Pull the shifter lever toward you to allow clearance for the bezel to be removed. Place the bezel aside when removed.
[Read the rest of this entry...]