Free PDF Manual Guide

This kit has been engineered to be an easy, bolt on upgrade to your standard Jackson Racing supercharger kit. It will raise your boost approximately 2 psi. As such, it has been designed to be a “Race Only” kit. Because of the “Race Only” design criteria, the C.A.R.B. Exemption Order number supplied with your Jackson Racing Supercharger Kit does NOT cover this product. Therefore, this racing boost upgrade is legal in California only on racing vehicles, which may never be used upon a highway. Other states may have laws governing the use of this product. Check local regulations before installation. Our kit was designed with and performs best when used with a good header, cat-back exhaust, and a good high flow air filter. Other non-specified accessories or engine components may affect your specific boost and horsepower output.
[Read the rest of this entry...]

This information is provided on the phone label. The label is on the back of the phone (under the battery). It contains the model and serial numbers, as well as other important information about your phone. See “Remove the back cover and battery” on page 8 for instructions on how to access the phone label. The label shows the following:
• Phone type
• Phone model
• IMEI
• FCC ID number

• SIM CARD INSTALLATION
Warning: Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor.

SIM card and battery
Before you begin, you need to prepare your phone by installing the SIM card and charging the battery. This chapter covers these topics, as well as instructions on how to attach the optional headset. Always switch off the phone before installing the SIM card and battery.
Remove the back cover and battery
1. With the back of the phone facing you, press and hold the back cover release button.
2. Slide the cover up; then lift it off the phone.
3. Lift out the battery

Download

The HONASX can either provide up to 2 auxiliary audio inputs to your Honda radio for use with any device that has RCA line level outputs, or provides 1 auxiliary audio input and allows interfacing an aftermarket CD Changer. AUX 1 is the 8 pin DIN to RCA cable which plugs into the 8 pin DIN port on the HONASX interface. AUX 2 is the set of RCAs that are wired directly to the HONASX. These audio inputs are perfectly suited for Multimedia devices such as VCRs, DVD’s, Game Systems or TV tuners. Portable music players such as MP3, MD and CD players can utilize these inputs as well.
[Read the rest of this entry...]

The jack should be used on firm and level ground 3 To lift the vehicle securely hold the jack lever and rod Carefully raise the vehicle until the tire clears the ground When using alternate rear jack up point for 15 inch wheels raise the vehicle so that the tire is no more than 2 inches 50 mm off the ground 4 Remove the wheel nuts and then remove the tire.
[Read the rest of this entry...]

Turn the ignition key to the OFF position and secure the steering wheel in a straight ahead position with a rope or similar device Never place the ignition key in the LOCK position This will result in damage to the steering lock mechanism Move the gearshift lever to the N Neutral position When towing with the rear wheels on the ground release the parking brake.
[Read the rest of this entry...]

This is what we’re starting with; a bone stock engine bay. The first step is to disconnect the negative battery cable. This will help to prevent any potential electrical problems, and also will “reset” the PCM so that the computer will be able to “re-learn” the engine with the new intake in place. To disconnect the battery cable, you will need a 10mm socket or wrench. (Note that this may erase your radio station presets, so you might want to write them down first, just in case.)
[Read the rest of this entry...]

The ECT Display Driver is a small module with a removable wire harness that mounts behind the driver’s foot well cover. All wiring connections are near the ECM and only 4 wires are needed for basic operation:
• +5v power from the ECM (T-tap)
• Ground – available at ECM mounting bolt
• ECT sensor wire (T-tap at ECM)
• Dash temperature gauge wire (must cut at ECM)

If you want to use the optional Alarm Output feature 3 more wires are needed:
• Ground (must be run separate from the module’s power ground)
• Module output (negative) to your alarm device (sounder or indicator light, not included)
• +12v ignition or accessory power wired directly to your alarm device
[Read the rest of this entry...]

Activating Your Phone
When you subscribe to a cellular network, you are provided with a plug-in SIM card loaded with your subscription details, such as your PIN, any optional services available, and many others.
[Read the rest of this entry...]

Compact Heat Pump Operating Instructions
Prior to use : -
1 Turn off the power supply at the local isolator
2 Open the door, using a coin or similar tool to unlock it
3 Check that the ground pressure gauge reads at least 0.3 bar. If the pressure is lower than this, open the mains cold water supply valve (fitted outside the case) fully until the gauge reads at least 1.8 bar, at which point a “click”will be heard. Close the mains cold water supply valve fully. If you can’t find this valve, or when you open it the gauge reading does not increase, call your installer and ask them about the mains cold water supply valve on the slinky ground array circuit.
[Read the rest of this entry...]

1 Connect the Power cord to the modem and a wall outlet or surge protector
2 Connect the Cable line from the Cable jack (or splitter) to the back of the modem.
3 Wait until the first four lights of modem are solid,
[Read the rest of this entry...]