Free PDF Manual Guide

Printer setting
1.1 Cable specifications (SRP-270, SRP-350, SRP-370/372)
- Use the serial cable that satisfies following specifications.
- If you don’t use incompatible cable, the printer may not work properly.*

Epson compatible cable mode
- IFA-S type and IFB-S type have Dip switch on the bracket
- Set the Dip switch on the interface card as following;
Bixolon Samsung compatible mode
Epson compatible mode
[Read the rest of this entry...]

The FLEDA System come with a one year parts & labor warranty. Also the FLEDA System has a 30 day money back, “no questions asked” return policy. You pay only for the shipping back to PAK BIKES.

The FLEDA and license plate bracket assemblies are NOT DOT approved and are for “off road” and “SHOW” use only. Purchaser assumes ALL responsibility for the proper installation of these systems. Improper installation of the FLEDA and license plate bracket [Read the rest of this entry...]

1) Disconnect negative battery cable and ground strap at transaxle. Disconnect positive battery cable. Remove battery and battery base. Remove drain plug, and drain transaxle fluid (remove fill plug to speed draining). Install drain plug with NEW washer, and tighten plug to specification. See TORQUE SPECIFICATIONS TABLE at the end of this article.
2) Disconnect wiring for starter motor, transaxle lock-up control solenoid and shift control solenoid. Remove starter. Disconnect mainshaft and countershaft speed sensor connectors. Remove complete air cleaner case assembly. Disconnect and remove throttle control cable at transaxle bracket.
[Read the rest of this entry...]

BMW D7 Marine Engine
A four-stroke diesel engine with direct injection and open-circuit cooling system. The Neoprene impeller of the coolant pump is driven directly from the crankshaft. Electric starter and flywheel alternator are standard equipment. The injection system is fitted with automatic bleeding.
[Read the rest of this entry...]

The diagram illustrates 8-3/4″ axles. The top is a 66-72 A-body axle. and the other two are longer axles that generally resemble the B and C body and truck axles. C body and truck axles can be shortened and resplined by a quality machine shop, however it is important to note that not all C-body/ Truck axles are created equally.
[Read the rest of this entry...]

Removal
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
[Read the rest of this entry...]

Before servicing propeller, be sure the engine is in neutral with ignition off or disconnected to avoid any possibility of the engine starting and causing injury. Do not install any propeller without a thrust washer in place. If a thrust washer is not used, severe damage could occur to the propeller and/or engine drive. Rotate prop in neutral by hand to make sure the prop rotates freely in full cycle. (If you have any questions, please contact your Dealer or call our Customer Service Department.)
[Read the rest of this entry...]

Before you can use the UPS monitoring software program, you need to install the cable connecting the UPS system to the serial port on the computer. All new UPS systems have the serial communications port on the back panel, labeled RS-232C. The cable for most UPS units is made with two male DB-9 connectors. It connects between the female DB-9 connector on the UPS rear panel and any compatible serial port on the computer. Be sure the cable is shielded and is terminated on the shell of the connector. This section describes cables connecting the UPS to a serial port on your computer. See the next section, “Switch Contact Port Cabling,” for information on constructing a cable to use the port labeled “UPS Port” on the back of many Alpha Micro computers.
[Read the rest of this entry...]

Carman Wi checks the vehicle defects by cable or wireless as a self-diagnostic sensor scan tool. As it is a compact size and wireless LAN communication type, users can diagnose the vehicle defects more quickly and conveniently.
※ Functional Summary
- Diagnostic function of Korean, Japanese, European, American Vehicles
- Vehicle communication function by Wireless LAN, USB method
- Work efficiency connecting the existing PC
- Saved Data Search function
[Read the rest of this entry...]

Installation Procedure:
1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Use a Philips head screwdriver to remove the 2 screws on either side of the console just behind the shift boot. Sliding the seats fully rearward allows easy access to these screws.
3. Slide the front seats fully forward and use a Philips head screwdriver to remove the 2 screws on either side of the back of the center console.
4. Lift the rear portion of the center console out of the car and put in a safe place for re-installation.
[Read the rest of this entry...]