Free PDF Manual Guide

Installation Procedure:
1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Use a Philips head screwdriver to remove the 2 screws on either side of the console just behind the shift boot. Sliding the seats fully rearward allows easy access to these screws.
3. Slide the front seats fully forward and use a Philips head screwdriver to remove the 2 screws on either side of the back of the center console.
4. Lift the rear portion of the center console out of the car and put in a safe place for re-installation.
[Read the rest of this entry...]

Front door trim, removing and installing
1 – Door trim
Remove screw cap – 5 -
Remove screw – 4 – (1x).
Unclip inner and outer connecting pieces. .
Lift door trim about 20 cm upward and remove from door.
Detach release cable for interior door handle
Disconnect electrical connectors
Clip locators – 3 – (7x) must be clipped in place when installing door trim.
[Read the rest of this entry...]

VAUXHALL / OPEL CORSA 1.2, 1.4 Spi 60BHP 1993-99 57-0298 Instruction Sheet A2054-796 Page 1 of 2 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. Note: the kit fits both models. Photo A Photo B 1. Unclip and remove the intake hose from the air box assembly. 2. Remove the air box hot air flap vacuum hose from the rear of the intake housing. Blank off the vacuum outlet pipe with the rubber plug supplied. 3. Unclip and remove the intake scoop from the front cross member and air box assembly. 4. Remove the flexi hose from between the exhaust manifold and the air box hot air flap. 5. Remove the air box assembly from the front mounting rubber, then slide the assembly out of the rear mounting grommets. Remove the assembly from the car. 1. Fit the new mounting bracket to the original rear air box mounting grommet
[Read the rest of this entry...]

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]

Install ULead Video Studio Plus – use full installation option
The following plugins need to be installed as part of the full installation
• Real Player
• QuickTime
• DirectX
• Windows Media Player
[Read the rest of this entry...]

Carman Wi checks the vehicle defects by cable or wireless as a self-diagnostic sensor scan tool. As it is a compact size and wireless LAN communication type, users can diagnose the vehicle defects more quickly and conveniently.
※ Functional Summary
- Diagnostic function of Korean, Japanese, European, American Vehicles
- Vehicle communication function by Wireless LAN, USB method
- Work efficiency connecting the existing PC
- Saved Data Search function
[Read the rest of this entry...]

VAUXHALL / OPEL 57-0005 Instruction sheet A2054-41-3 CAVALIER / ASCONA 1982-88 Astra / Kadett -1986 Page 1 of 3 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. If you have a problem, however small, call our Technical Department. Tel:- 01925 636950. Fax:- 01925 243111. Mon to Thurs 8.30 – 5pm. 1 Remove the plug from the Air Flow Meter (AFM). Release the hose on the intake pipe and remove the air box lid. Release the three remaining air box retaining screws and remove the air box base. 2 Remove the AFM from the air box lid and fit the new adaptor and gasket to the AFM with the four countersunk screws supplied. 3 Fit the mounting bracket to the AFM with the two screws supplied. 4. Cut out and position the template, tape in place, centre punch the two points and drill two holes 8.5mm diameter. Finally fit the
[Read the rest of this entry...]

New to Flash? Quirky things….
o Vector disappearing act (can be avoided now with the “object drawing” button)
o Pay attention to your timeline and label layers; it’s easy to get “inside” an object and not know where you are
o Know when to use what (graphic vs. movie clip)
o Circle at the top of a text box means single line, no wrap; resize box to get a square that will wrap
o Things don’t move right? Watch your “snaps” (Snap to object; magnets)
o When you create a graphic or movie clip, there is an anchor point. That’s the “axis” so if you are going to rotate the object using tweens, pay careful attention to the location of the “axis” (think about a clock; move point with Free Transform) NOTE: If you are rotating/animating with Actionscript, it uses the registration point instead
o Adding actions is easy, but you must be careful. Actionscript is case sensitive.
o More on actions: If you add to the frame, a little A will appear in the frame (Actions-Frame); if you add to an object, your Actions panel should say Actions-Button (or whatever object you are clicked on)
[Read the rest of this entry...]

Tools and Parts
- 1 K&N High-Flow Air Filter Model RC 4630
- 3 Iron Clips
- 3 6mm Bolts
- Acrylic Part

1st Step
- Disconnect the air pipe from MAF and airbox
- Remove the cover from the airbox
- Remove the original air filter
[Read the rest of this entry...]

Adobe Photoshop is the premiere image manipulation tool used by artists, photographers, designers, and hobbyists for both print and Web graphic design work. You have learned the basics and may have tried some advanced features of the program and you are ready for more. In this workshop, you will learn tips and tricks that will be helpful as you continue to learn more about this powerful program.
[Read the rest of this entry...]