Free PDF Manual Guide

Although this turbo system has been designed to use existing emissions controls (including catalytic converter), check local laws regarding aftermarket modification to emission controlled vehicles. Remove the turbocharger kit from its carton and inspect for any obvious physical damage. All kit components are thoroughly inspected and carefully packaged prior to shipment from the factory. If any shipping damage is evident, contact your supplier and request that they process a claim with the shipper involved. Be sure to review the Turbo System Parts List to verify that you have all necessary kit components to proceed. If any components in the parts list are missing, contact Turbonetics, Inc. Customer Service department.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

This interface connects an iPod directly to your Honda or ACURA audio system. lt’s on-board software translates commands from your Honda CD changer controls into commands that the iPod understands. This interface enables the iPod to take the place of a Honda CD changer and provides the following benefits:
Directs the iPod’s audio output to Honda vehicle audio system for optimal sound quality playback. Controls the iPod via vehicle’s radio and steering wheel controls. r Charges the iPod’s internal battery, and charging stops automatically at one hour after iPod is paused. iPod will go to SLEEP mode after charging
[Read the rest of this entry...]

Part Content:
This will also space out the entire wheel, widening the track width of the vehicle. Fender clearances should be checked on lowered cars, and longer lug studs or wheel bolts are usually required. Note: The Wheel Industry Council has issued guidelines advising wheel spacers not be used. It is the responsibility of the customer to insure wheel spacers are properly specified and installed.
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1996-2001 Honda Acura Integra Type R vehicles.
1. Please read through the entire instruction sheet to familiarize yourself with the installation before you begin.
2. Start the engine and check for loose connections or coolant/vacuum leaks, etc.
3. Disconnect the negative battery terminal.
4. Remove the air filter duct, all vacuum hoses, water (coolant) hoses and electrical connectors from the stock throttle body. Mark all hoses and wires to ensure that they are installed correctly on the new throttle body.
Note: Engine coolant may run from the hoses once disconnected. Plug the end of the hose temporarily.
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1994-2001 Acura Integra GSR 1.8L Vtec.
Throttle Body Kit Contents:
1 – Throttle body to manifold gasket
1 – Fast idle thermo valve o-ring with white stripe
1 – Fast idle thermo valve o-ring with red stripe
1 – Fast idle thermo valve o-ring with green stripe
1 – MAP sensor o-ring with blue strip
1 – E.O. # fan shroud decal
[Read the rest of this entry...]

What is the SmartMAP?
The SmartMAP model SS-300 replaces the check valve and restrictor assembly used by most Honda/Acura turbo and supercharger kits and prevents the engine computer (ECU) from shutting down the engine when the manifold pressure is above atmospheric (boost).

How does the SmartMAP work?
The SmartMAP connects inline with the stock (OEM) manifold absolute pressure (MAP) sensor and limits the MAP voltage that is applied to the ECU. The limit (clamp) voltage value is preset and can not be adjusted.
[Read the rest of this entry...]

1. The filter is located behind the glove compartment. Unscrew the 2 screws at the bottom of the glove box cover to loosen the it. Remove glove box and set it aside.
2. Cut the plastic cover along the dotted lines shown and remove it. Dispose off plastic cover, it is no longer needed. This exposes the metal cross bar under it. Locate and remove 2 additional bolts securing bar. Remove and set it aside.
[Read the rest of this entry...]

Remove all items from the packing tube. You should have the following before beginning:
* (2) Gas springs (RT-QL-120-10A) – Be sure to cycle them a few times before installing.
* (4) 3/16″- #1steel rivets (used on hood brackets)
* (2) ball-studs and washers
* (2) brackets used on hood frame
* Printed Color Instructions
* Gas Spring locking clips – (Already installed in the gas spring ball-ends-ball-studs/washers
[Read the rest of this entry...]

Removal
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
[Read the rest of this entry...]