Free PDF Manual Guide

1 2 3 4 5 6 7 8 8 9 9 9 9 10 10 11 11 11 A Plastic elements B Clamp mark in acc. with ISO PN Cables joining 1 L Left directional lights 2 + Rear fog lights 3 31 Ground 4 R Right directional lights 5 58R Right side parking lights 6 54 Stoplights 7 58L Left side parking lights FITTING INSTRUCTION This towbar is designed to assembly in following cars: OPEL CORSA “D”, 3/5 doors, produced since 2007, catalogue no. E50 and is prepared to tow trailers max total weight 1300 kg and max vertical load 50 kg. From manufacturer Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and right operation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install
[Read the rest of this entry...]

VAUXHALL / OPEL CORSA 1.2, 1.4 Spi 60BHP 1993-99 57-0298 Instruction Sheet A2054-796 Page 1 of 2 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. Note: the kit fits both models. Photo A Photo B 1. Unclip and remove the intake hose from the air box assembly. 2. Remove the air box hot air flap vacuum hose from the rear of the intake housing. Blank off the vacuum outlet pipe with the rubber plug supplied. 3. Unclip and remove the intake scoop from the front cross member and air box assembly. 4. Remove the flexi hose from between the exhaust manifold and the air box hot air flap. 5. Remove the air box assembly from the front mounting rubber, then slide the assembly out of the rear mounting grommets. Remove the assembly from the car. 1. Fit the new mounting bracket to the original rear air box mounting grommet
[Read the rest of this entry...]

This product is to be used ONLY on the Honda S2000 and is intended to provide increased driver support when using the stock lap belt and shoulder harness. It is NOT to be used as a replacement for competition belts or at any event where 4 or 5-point restraint systems are required. This product uses an electro-magnet to activate the factory inertia-sensing mechanism built into the seat belt assembly. It does not alter the factory restraint system in any way and has no effect on the seat belt retractors or air bag system. It simply activates the “tilt” mechanism built into the seat belt, the one that normally kicks in only when you corner or brake very hard. Modifry’s Seat Belt Lock is relatively easy to install and can be quickly removed, leaving no trace it was there.
[Read the rest of this entry...]

After car crashed and airbag had deployed, VW-Audi airbag sensor will stay locked
(Control unit faulty or deployed) and must be replaced. Even after small accident, Airbag sensor will write into it’s internal memory an error message “crash data stored” or “computer fault” and after it need to replace the expensive sensor to a new one. With our VAG Airbag Reset Tool you can reset and repair the airbag computer in your workshop in 1 minute. No need to remove airbag sensor from the car.
[Read the rest of this entry...]

After car crashed and airbag had deployed, VW-Audi airbag sensor will stay locked (Control unit faulty or deployed) and must be replaced. Even after small accident, Airbag sensor will write into it’s internal memory an error message “crash data stored” or “computer fault” and after it need to replace the expensive sensor to a new one. With our VAG Airbag Reset Tool you can reset and repair the airbag computer in your workshop in 1 minute. No need to remove airbag sensor from the car.
[Read the rest of this entry...]

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]

Seat belts must be worn on every journey, even on short trips in town. This applies to the front and rear seats. To ensure that the seat belts, belt tensioners and airbags are fully effective, please note the following points: Wear the seat belt correctly Make sure that the shoulder section of the belt is positioned over the centre of the shoulder and move the lap section as far down over the hips as possible. The belts should always be worn so that they fit tightly (see illustration). Adjust seat and sit in correct position The front seats should not be positioned too close to the steering wheel or dashboard. Main- tain a distance of at least 25 cm and sit in a normal upright position. The top of the head restraint should be at eye level or higher. Always keep your feet in the footwell.
[Read the rest of this entry...]

The advanced key allows you to lock and unlock the vehicle and start the engine without handling the key itself. You only need to have the remote control key on your person. Unlocking the vehicle Take hold of a door handle. The vehicle will be unlocked automatically. Locking the vehicle Briefly touch the locking sensor on one of the door handles. The selector lever must be in position P on vehicles with automatic gearbox. Note: If you keep hold of the sensor, this will also close the windows and the sun roof
[Read the rest of this entry...]

This guide has been prepared to help you get quickly acquainted with your new Mercedes-Benz and to provide a convenient reference source for common questions.

However, it is not intended as a substitute for your Operator’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Operator’s Manual and other warning labels in your truck.
[Read the rest of this entry...]

ZF Trading GmbH Obere Weiden 12 97424 Schweinfurt Germany © by ZF Trading GmbH 0032004_OSOPE019 OPEL Zafira Engine transmission Removing and fitting/replacing manual transmission. Remove: Lift vehicle. Remove lower engine cover. Dismount front exhaust tube Remove catalytic converter. Dismount central silencer. Remove water tank cover. Remove water tank insulation. (see Fig.1) Align engine/gearbox unit by means of holding devices. Remove front axle body Have steering wheel engage in straight position. Unscrew clamping joint. Detach intermediate spindle. (see Fig.2) Remove battery. Remove battery holder. Vehicles with petrol engine Disconnect lambda sensor connector. (see Fig.3) Secure radiator against falling down by Fig. 2 1 Clamping joint. Fig. 3 1 Lambda sensor connector. Fig. 4 1 Wire. No. Special tool Parts number Footnote Engine transmission 1 Engine support MKM-833-1 2 Adapter plate. MKM-883-2 3 Holding device(s) KM-909-B 4 Holding device(s) KM-6001-A Clutch 1 Blocking tool KM-652 2 Centering mandrel KM-734 F17 gearbox 3
[Read the rest of this entry...]