Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Installation instructions for Stratmosphere HyperBoost Valve

Bob and I appreciate your purchase of your HyperBoost Valve from Stratmosphere. Please read these instructions prior to installation so that you can enjoy a simple and quick installation of your new HyperBoost valve! –Pete
What’s included with your package:
• One HyperBoost diverter valve
• Two medium sized hose clamps
• One small hose clamp
• One instruction sheet (you are reading it)
[Read the rest of this entry...]

Leave a Comment

Acura B18 Valve Spring Set Instructions

The COMP Cams® Acura/Honda B-Series VTEC valve spring set (Fig. A) utilizes dual springs on the intake side and a single spring on the exhaust side. Below are the information and diagrams to ensure correct installation.
Installation Instructions:
Dual Intake Spring
Installed Height: 60lbs at 1.375
Open Height: 220 lbs at .875
Coil Bind Height: .815
Spring Rate: 300 lbs per inch
[Read the rest of this entry...]

Leave a Comment

1993-1998 VW Golf III 2.0L 8-valve B&M Short Shift System Instructions

This B&M Short Shift System has been designed to work on most 1993-1998 VW 2.0L 8-valve models. It has been engineered to greatly reduce shift throw and improve shift feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Shift System. Installation of the B&M Short Shift System can be accomplished by anyone with minimal mechanical experience.
[Read the rest of this entry...]

Leave a Comment

Fuel and exhaust systems – K-Jetronic fuel injection – 16 valve engines

The components of the K-Jetronic fuel injection system fitted to the 1.8 litre 16V engine are as shown (see illustrations). All procedures are the same as described in Part B of this Chapter except for those given in the following Sections.
2 Idle speed – adjustment
1. Run the engine to normal operating temperature, then check that all electrical components are switched off. Note that the electric cooling fan must not be running during the adjustment procedure.
[Read the rest of this entry...]

Leave a Comment

1992-2003 Volkswagen Golf, Jetta, GTI, Cabrio Heating Air Conditioning 87 – A/C controls and mechanical components, servicing

Installing and checking expansion valve insulator
1. Insulator
2. Expansion valve
Insulation is used around expansion valve to prevent moisture (condensation) build-up and to protect expansion valve from high engine compartment temperatures and the resulting decrease in A/C system cooling performance.
Install insulator – 1 – over expansion valve – 2 – (arrow).
Check insulator for damage and proper fit, and replace if necessary.
[Read the rest of this entry...]

Leave a Comment

TPMS Sensor Service Guidelines

This document outlines the guidelines for the manual mounting on the rim of EnTire/TRW fixed angle TPM sensors.
This document does not cover any other TPM sensors.
- Sensor & valve components
- Step 1 Start fitting the valve unit on the rim
- Step 2 Tighten the nut
- Step 3 Check the assembly sensor – valve – rim
[Read the rest of this entry...]

Leave a Comment

2001-02 Saturn SL1 Automatic Transmissions Saturn MP6 & MP7 Overhaul

Disassembly 1. Remove line actuator cover bolts. See Fig. 53 . Carefully remove cover and connector plate. Remove line actuators by twisting line actuator as it is pulled from valve body. 2. Remove through bolts. Separate valve body and separator plate. Remove check balls. See Fig. 54 . Remove manual valve. Remove each valve assembly. Retain in proper order for reassembly. See Fig. 55 and Fig. 56 .
[Read the rest of this entry...]

Leave a Comment

Compact Heat Pump Operation, Installation and Maintenance Manual

Compact Heat Pump Operating Instructions
Prior to use : -
1 Turn off the power supply at the local isolator
2 Open the door, using a coin or similar tool to unlock it
3 Check that the ground pressure gauge reads at least 0.3 bar. If the pressure is lower than this, open the mains cold water supply valve (fitted outside the case) fully until the gauge reads at least 1.8 bar, at which point a “click”will be heard. Close the mains cold water supply valve fully. If you can’t find this valve, or when you open it the gauge reading does not increase, call your installer and ask them about the mains cold water supply valve on the slinky ground array circuit.
[Read the rest of this entry...]

Leave a Comment

1991 Toyota Lexus ES 250 Service Manual

Recommend tools for engine repair. Engine tune up, inspection of engine coolant, inspection of engine oil, inspection of battery, inspection of air filter, inspection of high-tension cords, inspection of drive belts, remove cylinder heads cover : Turn the crankshaft pulley, and align its groove with the timing mark “0” of the No.1 timing belt cover. Check only those valves indicated in the figure, Using a feeler gauge, measure the clearance between the valve lifter and camshaft. Record out of specification valve clearance measurements.
[Read the rest of this entry...]

Leave a Comment

CAT-303 Installation and Parts Manual

Installation Environment
1) The distance between the unit and outside wall or other goods should be kept over 200mm.The unit should be put in well-ventilated area and its temperature is within -10℃~+40 .℃
2) Check air supply pipeline of the unit and use air source with 3~10 bar to supply for the unit. When connecting the air source, please check if there is leakage in connector for air source and ensure that a certain distance between the air hose and heat source should be kept.
3) To ensure safety. Before connecting the air source, please confirm that the air pressure adjusting valve is closed. Never point the air outlet to personnel.
[Read the rest of this entry...]

Leave a Comment