Free PDF Manual Guide

The BLADE installs easily onto round 1 7/8” to 2” diameter exhaust pipes. Important Notice: In order to install the BLADE, your car must:
• have an exposed, straight tailpipe measuring 1 7/8” – 2.0” in diameter. Example: 2004 Honda Civic
• or, dual exhaust pipes where there are 2 mufflers, each with a single exhaust pipe measuring 1 7/8” – 2.0” in diameter. Example: 2007 Lincoln Town car (in which case 2 BLADES are required).
If your car does not have either of these exhaust configurations, then your exhaust pipe will need modification. This modification is very easy to obtain at any exhaust shop i.e. Meineke, Midas, etc. Simply ask the technician to modify your tailpipe to meet this specification.
[Read the rest of this entry...]

This guide tells you how to install the Silicon Graphics 1600SW flat panel monitor adapter board in the O2 workstation. There are two classes of O2 workstations, the R5000, and the R10000. The 1600SW flat panel monitor adapter can be installed in either class of O2 workstation.
The guide is organized as follows:
• Chapter 1 describes how to install the adapter board in your O2 workstation.
• Chapter 2 describes how to adjust the flat panel timing tables and how to calibrate color for the 1600SW flat panel monitor.
• Chapter 3 provides troubleshooting information, technical specifications, and regulatory statements.
• The glossary defines many of the terms used in the manual.
[Read the rest of this entry...]

What’s Included:
1. The Model 80 enclosure bottom
2. The Model 80 vinyl covered enclosure top
3. Alumapro Alusonic 8 subwoofer (optional)
4. Subwoofer grille (optional)
5. Terminal cup
6. Self-adhesive gasket foam
7. Trim cord
8. (8) #10 x ¾” Phillips pan-head screws
9. (4) #14 x 1” hex-head sheet metal screws
10. (4) 1” fender washers
11. (4) 3/8 ” thick rubber washers
12. (12) 1 / 16 ” thick rubber washers
13. (4) #8 x ½” Phillips head machine screws
14. (4) #8 hex nuts
[Read the rest of this entry...]

Install the glove box door 6 Fill out the date information on the small replacement label and attach it to the glove box lid 8 18 Maintenance and do it yourself REVIEW COPY 2006 Xterra xtr Owners Manual USA English nna 08 01 05 debbie WINDSHIELD WIPER BLADES CLEANING.
[Read the rest of this entry...]

Bob and I appreciate your purchase of your HyperBoost Valve from Stratmosphere. Please read these instructions prior to installation so that you can enjoy a simple and quick installation of your new HyperBoost valve! –Pete
What’s included with your package:
• One HyperBoost diverter valve
• Two medium sized hose clamps
• One small hose clamp
• One instruction sheet (you are reading it)
[Read the rest of this entry...]

One of the biggest performance upgrades you can make to your XR or CRF 50 is to replace the stock semi auto clutch with a fully manual clutch. By adding a manual clutch, you can expect your 50 to launch harder out of corners, and you can also expect to get a faster jump off the starting line. For this “How To” article, we opted to use the proven 3- plate manual clutch kit from Honda Trail Bikes. This kit comes with everything you need except for the clutch lever and perch. With a little time and patience, the Trail Bikes clutch is fairly easy to install and is well worth the effort.
[Read the rest of this entry...]

The filters are marked with air flow arrows The end of the filter with the arrow should face the rear of the vehicle The arrows should face downward 3 Insert the first filter into the housing and slide it over to the right Insert the second filter into the housing 4 Replace the filter cover 5 Install the glove box door.
[Read the rest of this entry...]

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the air temperature sensor electrical connection as shown.
3. Unclip the battery cable from the air inlet duct as shown.
4. Loosen and remove the two bolts that secure the air inlet duct as shown.
5. Remove the air inlet duct.
[Read the rest of this entry...]

Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
[Read the rest of this entry...]

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]