Free PDF Manual Guide

Thank you for purchasing the PES G2 supercharger system. We have gone to great length to engineer this system to be a true bolt-on affair. Please read the entire instruction manual thoroughly before proceeding. If there is any part of the installation procedure that you are not comfortable with, please have a professional mechanic install the system.

PLEASE NOTE:
• The photos used in this manual were taken during the installation on a 2000 A4. There will be a special “NOTE” listed when there is a variation in the installation procedure.
• New PES supplied parts will be underlined in this manual.
[Read the rest of this entry...]

Following the steps for this Audi A4 Brake Installation Manual
PREPARATION FOR INSTALLATION
1. Be sure that the vehicle is parked on level concrete and the parking brake is on.
2. Place stops in front of and behind rear tires.
3. Consult owner’s manual for proper lifting and wheel removal procedures before lifting front of vehicle.
4. Place jack stands under vehicle for added stability.
[Read the rest of this entry...]

The Staff at AMS would like to take a moment to thank you for purchasing our product. We are confident that your purchase will provide you with many years of driving enjoyment. If you have any questions or concerns regarding this or any other product that we offer please don’t hesitate to contact us. We have a knowledgeable technical staff available to aid you in your decisions to improve your driving experience.
[Read the rest of this entry...]

Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
[Read the rest of this entry...]

Installation Environment
1) The distance between the unit and outside wall or other goods should be kept over 200mm.The unit should be put in well-ventilated area and its temperature is within -10℃~+40 .℃
2) Check air supply pipeline of the unit and use air source with 3~10 bar to supply for the unit. When connecting the air source, please check if there is leakage in connector for air source and ensure that a certain distance between the air hose and heat source should be kept.
3) To ensure safety. Before connecting the air source, please confirm that the air pressure adjusting valve is closed. Never point the air outlet to personnel.
[Read the rest of this entry...]

BMW E65/66 Interface Installation Manual
Caution before working
1. Before installation, be sure to key off and wait more than 5 minutes for complete discharge of electricity
2. Don’t turn on the ignition during connectors are disconnected, because if you turn on the ignition with disconnected connectors, ECU falsely recognize status of car as an error and display error code on monitor
3. Be sure to use the tools of proper size and usage.
4. Don’t try to dissemble and assemble by force
5. Use proper tape or soft fabric to protect car from scratch or damage
6. Be sure to use power line from cigar lighter. In the case that you cannot use power line from cigar lighter, be sure to use a relay to protect interface from electric shock
[Read the rest of this entry...]

It is preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the shifter cable bushings on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
Estimated Installation Time: 30 minutes
Tools required:
▪ Ratchet
▪ 10 mm deep socket
▪ Ratchet extension
▪ Needle nose pliers/vise grips
[Read the rest of this entry...]

Installation Procedure:
1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Use a Philips head screwdriver to remove the 2 screws on either side of the console just behind the shift boot. Sliding the seats fully rearward allows easy access to these screws.
3. Slide the front seats fully forward and use a Philips head screwdriver to remove the 2 screws on either side of the back of the center console.
4. Lift the rear portion of the center console out of the car and put in a safe place for re-installation.
[Read the rest of this entry...]

Mounting the Control Module
1. Choose a location that is away from hot or moving parts that may interfere with the components or their wires. Prevent access to the components as much as possible by mounting them in hidden locations.
2. The internal tilt sensor will be most sensitive when the control module is oriented so that it sits horizontal. Test different orientations of the module before final placement to ensure proper activation of the tilt sensor. Below is a diagram of suggested mounting positions applicable to all motorcycles. Any position where the ‘Talon’ logo on the module faces directly to the side of the motorcycle (and is spun 360 degrees around this axis) will NOT work. Keep in mind that the alarm can be mounted upside down or rest at any angle due to the self-referencing technology used in the tilt sensing mechanism. Mount the control module with the supplied adhesive tape or use the supplied screws.
[Read the rest of this entry...]

This manual describes the installation, programming and operation of the Samsung SVM-800 Voice Mail System. It is intended to be read by people installing, maintaining or programming the SVM-800. The DCS SVM-800 is a Voice Mailing System which integrates currently with the DCS Compact II and DCS-VIP telephone systems*. The system has capacity for up to 8 digital extension ports.
[Read the rest of this entry...]