Free PDF Manual Guide

Whether you buy or lease a Honda vehicle, Honda Financial Services can assist you with the process. Please ask your dealer which lease or purchase plan best suits your needs. Want your own look? Ask your dealer about Honda Genuine Accessories.They’re designed, engineered and tested to meet the same exacting standards as your new vehicle – and a high-quality way to make your new Honda a reflection of your one-of-a-kind personality.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Specially designed adapters are used in conjunction with Universal Anchoring System (UAS) stands and Universal Measuring System (UMS) pinchweld stands when securing vehicles with horizontal pinchwelds and vertical jack tabs in the corners of their center sections. (All Honda / Accord / Acura vehicles excluding Odessey.) These adapters allow the positioning of vertical jack tabs into a slot on the adapter’s top surface, and the attachment of 4 inch clamps to horizontal pinch-welds.
[Read the rest of this entry...]

Tools Needed To Complete This Install Hand tools needed Accessory tools needed to test and to remove radio wire the new radio PLUS: Wire ties or electrical tape: to neatly bundle and organize your wires for a professional appearance. TOOL TIPS: Small Battery: use a battery to test speaker wires. Touching the (+) positive and (-) negative baterry leads to a pair of speaker will cause the speaker to make a “Pop” sound indicating that pair of wires goes to that speaker. Voltage Meter: Always check +12 Volt power wires for voltage before making wire connections. These wires will fluctuate between 10 and 14 Volts. Solder Iron or Crimp Tool: make wire to wire connections using either a solder iron and electrical tape, OR plastic crimp terminals found at most hardware or auto parts stores.
[Read the rest of this entry...]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

NOTE:
• Be careful not to damage the body paint finish.
• This trunk spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• Wash and wax the area to be covered. Use a
high-quality paste wax.
[Read the rest of this entry...]

STEP 1: Adjust hood until proper alignment with matching panels is achieved.
STEP 2: Adjust primary latch until it fits into the bar on the hood. Make sure when the hood is closed you can hear the latch “click” onto the hood.
STEP 3: After you here it click, test it to be sure it’s working properly by grabbing the front edge of the hood and slowly pulling upward with a steady even pressure. If the hood opens it’s not adjusted properly; repeat STEP 2 until hood cannot be pulled open after it’s closed.
[Read the rest of this entry...]

The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet-air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. Because of the increased airflow and reduced inlet temperature, the air-mass flow to the engine increases, this translates to more power.
[Read the rest of this entry...]

Congratulations! You have just purchased the best engineered, dyno-prove intake system available. Please check the contents of this box immediately. Report any defective or missing parts to the Authorized Injen Technology dealer you purchased this product from. Before installing any parts of this system, please read the instructions thoroughly. If you have any questions regarding installation please contact the dealer you purchased this product from. Installation DOES require some mechanical skills. A qualified mechanic is always recommended. *Do not attempt to install the intake system while the engine is hot. The installation may require removal of radiator fluid line that may be hot. Injen Technology offers a limited lifetime warranty to the original purchaser against defects in materials and workmanship. Warranty claims must be handled through the dealer from which the item was purchased.
Note: Disconnect the negative battery teriminal before starting this installation.
1 Remove the air intake box cover and intake air intake duct leading to the throttle body.
2 Remove the PCV pipe as seen in figure 4 and replace the water bypass valve with the 15”- 6mm hose provided in the kit. The coolant line port is located on the intake manifold housing . See diagram’s A or B The location of the coolant line port hose may vary depending on the year of your car. ( Do not attempt to remove any lines until your engine is cool to the touch.)
3 All Ex-models 94-97- Remove all of the components as seen in diagram C- #8. Since the cold air intake is not being used in this application the air resonator box can remain in the stock location. Once the components have been removed from the metal pipe leading to the EGR valve, you may cap-off or plug as indicated in figure 6 and diagram C. Use the 5mm vacuum cap to seal the line.
4 Screw the vibra-mount into the fender wall as seen in figure 3 and use the m6 nut and washer to attach it.
5 Place the step hose onto the throttle body and use two clamps and tighten the clamp on the throttler body at this point. See fig. 2
6 Place the end of the intake with the 1/2” aluminum nipple into the 3” side of the step hose and align the bracket on the intake to the vibra-mount stud and semi-tighten the nut and clamp. See figs. 5 and 7

Source

Getting Started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake. Install rear wheel chocks.
c) If the engine has run with in the past two hours let it cool down.
d) Jack the front of the vehicle and support using properly rated jack stands.
e) Remove the left front wheel.
[Read the rest of this entry...]