Free PDF Manual Guide

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]

VAUXHALL / OPEL CORSA 1.2, 1.4 Spi 60BHP 1993-99 57-0298 Instruction Sheet A2054-796 Page 1 of 2 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. Note: the kit fits both models. Photo A Photo B 1. Unclip and remove the intake hose from the air box assembly. 2. Remove the air box hot air flap vacuum hose from the rear of the intake housing. Blank off the vacuum outlet pipe with the rubber plug supplied. 3. Unclip and remove the intake scoop from the front cross member and air box assembly. 4. Remove the flexi hose from between the exhaust manifold and the air box hot air flap. 5. Remove the air box assembly from the front mounting rubber, then slide the assembly out of the rear mounting grommets. Remove the assembly from the car. 1. Fit the new mounting bracket to the original rear air box mounting grommet
[Read the rest of this entry...]

VAUXHALL / OPEL 57-0005 Instruction sheet A2054-41-3 CAVALIER / ASCONA 1982-88 Astra / Kadett -1986 Page 1 of 3 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. If you have a problem, however small, call our Technical Department. Tel:- 01925 636950. Fax:- 01925 243111. Mon to Thurs 8.30 – 5pm. 1 Remove the plug from the Air Flow Meter (AFM). Release the hose on the intake pipe and remove the air box lid. Release the three remaining air box retaining screws and remove the air box base. 2 Remove the AFM from the air box lid and fit the new adaptor and gasket to the AFM with the four countersunk screws supplied. 3 Fit the mounting bracket to the AFM with the two screws supplied. 4. Cut out and position the template, tape in place, centre punch the two points and drill two holes 8.5mm diameter. Finally fit the
[Read the rest of this entry...]

Tools Required:
Phillips Screwdriver
Screwdriver
8mm Nut driver
10mm wrench

Parts Included:
EVO High Flow Cotton Air Filter X1
EVO Plastic 6” Venturi X1
EVO Billet Aluminum Venturi Tube X1
EVO Heat shield w/ Spring
Clamp Installed X1
EVO Heat shield cover w/
Stainless V-Flow Tag X1
Hose clamps X2
10mm Bolts X3
Small washers X3
Breather Filter X1
[Read the rest of this entry...]

Installation Environment
1) The distance between the unit and outside wall or other goods should be kept over 200mm.The unit should be put in well-ventilated area and its temperature is within -10℃~+40 .℃
2) Check air supply pipeline of the unit and use air source with 3~10 bar to supply for the unit. When connecting the air source, please check if there is leakage in connector for air source and ensure that a certain distance between the air hose and heat source should be kept.
3) To ensure safety. Before connecting the air source, please confirm that the air pressure adjusting valve is closed. Never point the air outlet to personnel.
[Read the rest of this entry...]

Read and understand these instructions BEFORE attempting to install this product.
1) Getting started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake.
c) Make sure you have the anti-theft code for the radio.
d) Disconnect negative battery terminal.
e) If engine has run within the past two hours let it cool down.
[Read the rest of this entry...]

Installation Procedure:
1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Use a Philips head screwdriver to remove the 2 screws on either side of the console just behind the shift boot. Sliding the seats fully rearward allows easy access to these screws.
3. Slide the front seats fully forward and use a Philips head screwdriver to remove the 2 screws on either side of the back of the center console.
4. Lift the rear portion of the center console out of the car and put in a safe place for re-installation.
[Read the rest of this entry...]

In order to use the Floating Pump to pump water from a dam, swimming pool or large tank into your Silvan spray equipment, simply attatch the 2 ½” BSP fitting on the 64mm lay flat hose supplied, to the 2 ½” BSP outlet of the Floating Pump. Next, either attatch the outlet end of the hose to the inlet of your spray equipment using the camlock fitting supplied, or simply place the outlet of the lay flat hose into the fill opening on the spray equipment. Place the Floating Pump into the dam, swimming pool or tank, ensuring the water is deep enough below the pump inlet to prevent mud etc from being drawn up from the bottom of the dam, swimming pool or tank and into the pump.
[Read the rest of this entry...]

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
[Read the rest of this entry...]

Front door trim, removing and installing
1 – Door trim
Remove screw cap – 5 -
Remove screw – 4 – (1x).
Unclip inner and outer connecting pieces. .
Lift door trim about 20 cm upward and remove from door.
Detach release cable for interior door handle
Disconnect electrical connectors
Clip locators – 3 – (7x) must be clipped in place when installing door trim.
[Read the rest of this entry...]