Free PDF Manual Guide

One of the biggest performance upgrades you can make to your XR or CRF 50 is to replace the stock semi auto clutch with a fully manual clutch. By adding a manual clutch, you can expect your 50 to launch harder out of corners, and you can also expect to get a faster jump off the starting line. For this “How To” article, we opted to use the proven 3- plate manual clutch kit from Honda Trail Bikes. This kit comes with everything you need except for the clutch lever and perch. With a little time and patience, the Trail Bikes clutch is fairly easy to install and is well worth the effort.
[Read the rest of this entry...]

Oracle 10g R2 is latest release and at the time of document creation is only supported on x86. Novell SUSE LINUX Enterprise Server 9 (SLES9) certification is in progress and will be updated on Metalink (http://metalink.oracle.com/). This document will help you to install Oracle 10g R2 on SLES9. If you encounter any problem, please post your question to suse-oracle@suse.com.

Note: Same instruction will work for SUSE LINUX Professional 9.3 but not supported by Novell/Oracle in production environment.
[Read the rest of this entry...]

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the air temperature sensor electrical connection as shown.
3. Unclip the battery cable from the air inlet duct as shown.
4. Loosen and remove the two bolts that secure the air inlet duct as shown.
5. Remove the air inlet duct.
[Read the rest of this entry...]

Your DVR box can support a variety of video and audio formats, including standard-definition and high-definition TV, and analog and digital audio. With this versatility, your DVR box can be connected to a basic TV and VCR or it can be easily incorporated into a high-end home entertainment center.
[Read the rest of this entry...]

This is what we’re starting with; a bone stock engine bay. The first step is to disconnect the negative battery cable. This will help to prevent any potential electrical problems, and also will “reset” the PCM so that the computer will be able to “re-learn” the engine with the new intake in place. To disconnect the battery cable, you will need a 10mm socket or wrench. (Note that this may erase your radio station presets, so you might want to write them down first, just in case.)
[Read the rest of this entry...]

Tools and Parts
- 1 K&N High-Flow Air Filter Model RC 4630
- 3 Iron Clips
- 3 6mm Bolts
- Acrylic Part

1st Step
- Disconnect the air pipe from MAF and airbox
- Remove the cover from the airbox
- Remove the original air filter
[Read the rest of this entry...]

Monitor Installation Steps
1. Power off your computer.
2. Connect the signal cable to the monitor and then to your computer.
3. Connect the power cable to the monitor and to a wall outlet.
4. Power on your computer, your monitor, and the “vacation switch” on the left side of the monitor.
[Read the rest of this entry...]

Installation
1. Begin by removing the battery, battery tray and fuse box.
2. Locate and remove the factory ECU under the passenger side dash.
3. Remove the factory engine harness from the engine bay and under the dash. There will be 2 10mm bolts under the battery tray holding the harness in place. Remove this plate/grommet to reuse with your K series engine harness.
[Read the rest of this entry...]

Compact Heat Pump Operating Instructions
Prior to use : -
1 Turn off the power supply at the local isolator
2 Open the door, using a coin or similar tool to unlock it
3 Check that the ground pressure gauge reads at least 0.3 bar. If the pressure is lower than this, open the mains cold water supply valve (fitted outside the case) fully until the gauge reads at least 1.8 bar, at which point a “click”will be heard. Close the mains cold water supply valve fully. If you can’t find this valve, or when you open it the gauge reading does not increase, call your installer and ask them about the mains cold water supply valve on the slinky ground array circuit.
[Read the rest of this entry...]

The K&Nо Drycharger included with this kit must be installed on the K&Nо air filter when used with this K&Nо cold air intake system. The K&N cold air intake system a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your cold air intake system to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.
[Read the rest of this entry...]