Free PDF Manual Guide

Shopping list from FORD dealer, $15.00 for 2 sets of heater hose o-rings and snap clips, $40.00 heater core, (cheaper at the dealer but no warrantee, aftermarket parts store model preferred by many @ $55) insulated foam tape to wrap new core with (parts dept just gave me what I needed), and a gallon of anti freeze.
[Read the rest of this entry...]

MANUAL AIR CONDITIONER: Heater Control Name Sheet No. 2 Air Conditioner Amplifier Assy Integration Control & Panel Bulb x5 Heater Control Housing Sub−assy Heater Control Housing Heater Blower Switch Radio Bracket No. 1 Heater Control Name Sheet No. 1 Control Knob Sub−assy AUTO AIR CONDITIONER: Heater Control Housing Sub−assy Control Knob Sub−assy Integration Control & Panel Bulb x9 Glove Compartment Door [Read the rest of this entry...]

Evaporator Case Assembly The evaporator case assembly is attached to the engine side of the dash panel. The case is a two-piece molded construction, one piece of which forms a cover over the evaporator core. An integral vacuum reservoir is part of the cover housing. This reservoir and the vacuum motor, which operates the outside/recirc air door, are linked through a check valve to a hose that supplies engine vacuum. The blower housing is an integral part of the evaporator case. It houses the blower motor and wheel assembly which attaches to the case through a mounting flange on the blower motor. The blower motor resistor assembly is attached to the case with its thermal elements extending into the air stream inside the evaporator case. The suction accumulator/drier is attached to the evaporator core by a support bracket.
[Read the rest of this entry...]

COMPRESSOR CLUTCH CONTROL
Evaporator Temperature Switch
Although compressor clutch does not normally cycle on and off, an evaporator temperature switch turns off the compressor clutch if evaporator temperature decreases to 32øF (0øC). This prevents evaporator icing.

A/C Pressure Switch
A/C pressure switch is a triple-pressure switch, which monitors high side pressure. See Fig. 1. If pressure decreases to less than 17.4 psi (1.2 kg/cmý), A/C pressure switch interrupts power to compressor clutch (low-pressure cutout). Switch closes when pressure increases to more than 34.8 psi (2.4 kg/cmý).
[Read the rest of this entry...]

The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation.
[Read the rest of this entry...]

Installation Environment
1) The distance between the unit and outside wall or other goods should be kept over 200mm.The unit should be put in well-ventilated area and its temperature is within -10℃~+40 .℃
2) Check air supply pipeline of the unit and use air source with 3~10 bar to supply for the unit. When connecting the air source, please check if there is leakage in connector for air source and ensure that a certain distance between the air hose and heat source should be kept.
3) To ensure safety. Before connecting the air source, please confirm that the air pressure adjusting valve is closed. Never point the air outlet to personnel.
[Read the rest of this entry...]

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
[Read the rest of this entry...]

In order to use the Floating Pump to pump water from a dam, swimming pool or large tank into your Silvan spray equipment, simply attatch the 2 ½” BSP fitting on the 64mm lay flat hose supplied, to the 2 ½” BSP outlet of the Floating Pump. Next, either attatch the outlet end of the hose to the inlet of your spray equipment using the camlock fitting supplied, or simply place the outlet of the lay flat hose into the fill opening on the spray equipment. Place the Floating Pump into the dam, swimming pool or tank, ensuring the water is deep enough below the pump inlet to prevent mud etc from being drawn up from the bottom of the dam, swimming pool or tank and into the pump.
[Read the rest of this entry...]

This tutorial was written due to my frustration on installing Oracle 9i on FC3. Basically 9i installation on RAS 1,2,3 RH 9, FC1, FC2 is documented fairly well but it is hard to find anything worthwhile on FC3; some people even suggested that installing Oracle 9i on FC3 is not possible. This HOWTO attempts to condense all my experience and findings with any such info peculiar to FC3, which was before scattered all over the web, into one concise but useful document.
[Read the rest of this entry...]

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]