Free PDF Manual Guide

TURNING THE RADIO ON OR OFF:
Turn on/off/volume control: (control #1 on attached
radio diagram)
Clockwise = on
Counterclockwise = off

SELECTING ZONE (BANK):
The radio is equipped with three zones or banks labeled A, B, and C, which are controlled by the toggle switch (control #4).
A = (Always) it the primary operational setting and should be used for routine operation.
B = (Backup) it is the redundant backup zone should the A-bank fail. If your radio says “Site Trunking” or “Fail Soft” in LED screen switch to the B-bank. C = (Cause) switch to this bank beCause someone told you to.
SELECT THE DESIRED MODE (TALKGROUP): Modes are also known as channels or talkgroups. Each radio can have up to 16 talkgroups per bank. (See the talkgroup listings and key for your radio group.) Select the desired talkgroup with mode control knob (#2). The LED display shows the talkgroup name.
[Read the rest of this entry...]

Tools Needed To Complete This Install Hand tools needed Accessory tools needed to test and to remove radio wire the new radio PLUS: Wire ties or electrical tape: to neatly bundle and organize your wires for a professional appearance. TOOL TIPS: Small Battery: use a battery to test speaker wires. Touching the (+) positive and (-) negative baterry leads to a pair of speaker will cause the speaker to make a “Pop” sound indicating that pair of wires goes to that speaker. Voltage Meter: Always check +12 Volt power wires for voltage before making wire connections. These wires will fluctuate between 10 and 14 Volts. Solder Iron or Crimp Tool: make wire to wire connections using either a solder iron and electrical tape, OR plastic crimp terminals found at most hardware or auto parts stores.
[Read the rest of this entry...]

Your radio has two programmable buttons. Your dealer can program these buttons as shortcuts to various radio features. Check with your dealer for a complete list of functions your radio supports. Programmable buttons include the g and h buttons (see page 9).
[Read the rest of this entry...]

Howler Concept Vehicle – The information contained in this guide has been prepared for use by persons installing two-way radio equipment (transmitters and receivers) in vehicles. It has been prepared in accordance with current engineering principles and generallyaccepted practices, using the best information available at the time of publication. It is not possible to cover all of the possible installations of two-way radio equipment in this guide. Accordingly, DaimlerChrysler Corporation cannot be held responsible for incidental or consequent damages arising out of the use of the information contained herein. Installations and modifications are solely the customer’s responsibility
[Read the rest of this entry...]

SIRIUS has 65 original music channels, from today’s hits to R&B oldies to classical masterpieces. From authentic Country and real Bluegrass to cool Jazz, hot Latin, Reggae, Rock and many more. Best of all, it’s all completely commercial-free.
[Read the rest of this entry...]

Ford Motor Company vehicles are designed and tested for safe operation with properly installed and properly used land mobile/amateur radio communication equipment with up to 100 Watt transmitter power.
Special design considerations are incorporated into all Ford vehicle electronic systems to provide immunity to radio frequency signals. To maintain compatibility with vehicle electronic systems, mobile two-wayradio and telephone equipment must be installed properly by trained personnel, observing these general guidelines:
[Read the rest of this entry...]

Subject:
i-Honda-R DICE iPod Integration Kit for Honda/Acura, Radio Interface Kit
Installation Instructions:
1. Pull vehicle into service bay and access center console.
2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when it is connected.
Make sure you have the vehicle’s radio security code before disconnecting the battery cables! Detailed steps for removing the Honda/Acura radio can be found in your factory manual this supplement will ONLY show an outline for radio removal.
3. Remove any trim that may need to be removed to gain access to the screws/bolts holding the radio in place. On some vehicles, this may require removing the trim around the shifter and removing the coin and cup holders, finally getting to the trim surrounding the radio.
[Read the rest of this entry...]

This handout is provided to guide you through the steps necessary to upgrade your vehicle with one of our performance chips. Also be aware that APR is only a phone call away should you every have any questions or concerns pertaining to any APR products.

Step 1: Park Car.
Insure car is off and key is out of ignition. Engage the parking brake. (Optional): Remove Battery Cable. Caution! Before disconnecting the battery, determine the correct coding for the anti-theft radio.
[Read the rest of this entry...]

Honda’s S2000 is famous for its high revving engine, but also infamous for its low- view factory radio placement. Not only is Honda’s factory radio placed very low in the dash, but it is also only single-DIN. While single-DINs were the norm in Japanese cars years ago, today most Japanese cars are double-DIN. Ernest Ornate and Junior Ngim of Sound Innovations in Hayward, Calif., show a great way to put a double-DIN video unit higher up in the dash of a Honda S2000. Ernest notes to make sure to inform the customer that he will lose airflow to the passenger air vent due to the removal of all ductwork leading from the blower motor to the vent.
[Read the rest of this entry...]

Remove the bezel that surrounds the climate control and extends behind the transmission shifter. To do this, grasp the bezel behind the shifter and release the first clip. In the upper-right corner of the bezel, use the Dash Trim tool to work loose the remaining ten (10) clips that hold the bezel in place. Note: On vehicles without the navigation system and/or with the DVD, the climate controls will come off with the bezel. Note: On vehicles that have the navigation system, disconnect the emergency light switch connector, and interior lighting switch. Apply the emergency brake and turn the ignition to the on position. Place the transmission shifter into the neutral position. Pull the shifter lever toward you to allow clearance for the bezel to be removed. Place the bezel aside when removed.
[Read the rest of this entry...]