Free PDF Manual Guide

his kit is designed to fit both the 120&160 engine platforms. The only difference you will find between the 120 and the 160 engine is the direction the cable adjustment block is installed on the engine block.
1. Remove the stamped factory linkage plate and related hardware.
2. Check your carburetor and confirm the throttle arm (black plastic molded arm on the top of the throttle shaft) is in good working condition.
3. Install the Linkage Bridge to your engine using the two supplied metric socket head bolts. A drop of thread locking compound on each bolt is recommended to prevent bolts from coming loose from vibration and harmonics.
[Read the rest of this entry...]

This Dash Mount is designed for: Location: Tools Required: Monteringsanvisning Mounting Instruction Do not use force when working with plastic components. Use extreme care not to scratch the interior of the vehicle. MTU may not be held liable for any damage to a vehicle connected to the installation. Correct direction of the rose pattern. Steg 1: Under askebegret i bunnen av midtkonsollet finner du en torx-20 skrue som du skrur ut. Skyv så hele askebeger enheten, med panel, rett ned. Steg 2: Under varneapparat-panelet funner du 2 torx-20 skruer som skrus ut. Grip tak i hele panelet og trekk det rett ut. Dette er festet med 3 klips i overkant og det midterste kan trenge litt hjelp ifra et bendeverktøy. Steg 3: Ta av beskyttelses tapen på Dash Mounten og huk den over panelets høyre øvre kant. Trekk godt inn. Steg 4: Monter det hele tilbake på plass i motsatt
[Read the rest of this entry...]

ZF Trading GmbH Obere Weiden 12 97424 Schweinfurt Germany © by ZF Trading GmbH 0032004_OSOPE019 OPEL Zafira Engine transmission Removing and fitting/replacing manual transmission. Remove: Lift vehicle. Remove lower engine cover. Dismount front exhaust tube Remove catalytic converter. Dismount central silencer. Remove water tank cover. Remove water tank insulation. (see Fig.1) Align engine/gearbox unit by means of holding devices. Remove front axle body Have steering wheel engage in straight position. Unscrew clamping joint. Detach intermediate spindle. (see Fig.2) Remove battery. Remove battery holder. Vehicles with petrol engine Disconnect lambda sensor connector. (see Fig.3) Secure radiator against falling down by Fig. 2 1 Clamping joint. Fig. 3 1 Lambda sensor connector. Fig. 4 1 Wire. No. Special tool Parts number Footnote Engine transmission 1 Engine support MKM-833-1 2 Adapter plate. MKM-883-2 3 Holding device(s) KM-909-B 4 Holding device(s) KM-6001-A Clutch 1 Blocking tool KM-652 2 Centering mandrel KM-734 F17 gearbox 3
[Read the rest of this entry...]

This document is intended as an update towards the progress of our project group in ME344-Machine Design on the manual transmission design project. Our rst assignment was to project values for the spacing between the in- put/mainshafts and the countershaft ( c ), as well as the diametrical pitch for the gears ( P ). With these values set as variables, we were able to determine the diameter of each of the twelve gears ( d 1 ; d 2 ::: ), and number of teeth per gear ( N 1 ; N 2 ; ::: ). All of the calculations were assuming the design to be of spur gears, and were to be calculated based o given information from project state- ment (ie. with particular interest to desired gear ratios for selected speed of transmission).
[Read the rest of this entry...]

AMSOIL Synthetic Manual Transmission and Transaxle Gear Lube (MTG) is a premium blend of the finest synthetic base oils and advanced, high-performance additives. It is formulated specifically for maximum protection in the most demanding manual transmission and transaxle applications where an extreme pressure GL-4 gear lube is specified, including those where high horsepower/high torque engines and towing or heavy loads increase transmission stress.
[Read the rest of this entry...]

Here are the steps for Mercedes-Benz E-Class Interface W211 Installation/Connection:
1. Interface module full-set
2. Remote function & connection feature
3. Disassemble guide
To connect interface , have to release command system and Gear box in the circle
After Shift -Lever on Drive- mode , Pull out gearbox as arrow direction
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1996-2001 Honda Acura Integra Type R vehicles.
1. Please read through the entire instruction sheet to familiarize yourself with the installation before you begin.
2. Start the engine and check for loose connections or coolant/vacuum leaks, etc.
3. Disconnect the negative battery terminal.
4. Remove the air filter duct, all vacuum hoses, water (coolant) hoses and electrical connectors from the stock throttle body. Mark all hoses and wires to ensure that they are installed correctly on the new throttle body.
Note: Engine coolant may run from the hoses once disconnected. Plug the end of the hose temporarily.
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1994-2001 Acura Integra GSR 1.8L Vtec.
Throttle Body Kit Contents:
1 – Throttle body to manifold gasket
1 – Fast idle thermo valve o-ring with white stripe
1 – Fast idle thermo valve o-ring with red stripe
1 – Fast idle thermo valve o-ring with green stripe
1 – MAP sensor o-ring with blue strip
1 – E.O. # fan shroud decal
[Read the rest of this entry...]

With the Audi advanced key you can start the engine without having to insert the key in the ignition lock. You only need to have the remote control key on your person. Switching on the ignition: Press the START button r briefly down to the first stop (diesel engines: preheating starts in this position). Starting the engine: Press the brake pedal and press START button r down to the second stop on a vehicle with automatic gearbox. Switching off the engine: Stop the vehicle, move the selec tor lever to position P or N and press the STOP button e.
[Read the rest of this entry...]

The wide ratio version is available for all F Series vehicles over 8500 lbs GVW all engines 6007 except F Super Duty Commercial Stripped Chassis equipped with a diesel engine The close ratio version is available only in F Series vehicles with a 7 3L diesel engine and a GVW over 8500 lbs.
[Read the rest of this entry...]