Free PDF Manual Guide

1. The Grout Hog® is a material delivery system and is not intended for any other use.
2. Make sure anyone operating the Grout Hog® is thor- oughly familiar with its operation. Keep all unauthorized and untrained personnel, especially children, away from Grout Hog®.
[Read the rest of this entry...]

This kit is designed to fit the 1995 and newer AX15 transmission. Earlier model transmissions can use a stock pilot bushing, one with a .590″ I.D. We recommend that the stock flywheel be removed and resurfaced at a machine shop. A new clutch disc and release bearing has been provided in this kit. A new pressure plate is also recommended before installing your new transmission. We offer a Centerforce pressure plate, Part No. CF361914. Before disposing of the old AX5 transmission, you will need to retain the shifter housing from that transmission. You will also be using the stock 4 cylinder bellhousing and stock release arm and crossmember mount.
[Read the rest of this entry...]

Preparation Steps for Fuel System Installation
A: Adjust both seats to full forward position with seat backs in full upright position.
B: Disconnect the negative battery cable.
C: Remove the 5 rear interior panels starting with the long piece across the width of the car just beneath the rear glass. Next remove the two flat panels located behind the seats. Next remove the two corner pieces. Lastly, remove the rear center speaker and cover assembly. (The long panel across the width has 3 push lock barbed style securing pins w/one on each end and one in the center) (The 2 flat panels have 4 push lock barbed securing pins each, w/each barb located a couple of inches from each corner of the panels) (The corner sections are held in place with 3 Philips screws which become exposed after the flat panels are removed)
[Read the rest of this entry...]

The IDB-HCS12E Evaluation Board demonstrates the capabilities of the 112-pin MC9S12E128 device. The IDB-HCS12E Evaluation Board can be used as a standalone application or with an emulator system, such as inDART-HCS12, through a standard BDM connection.
[Read the rest of this entry...]

1 2 3 4 5 6 7 8 8 9 9 9 9 10 10 11 11 11 A Plastic elements B Clamp mark in acc. with ISO PN Cables joining 1 L Left directional lights 2 + Rear fog lights 3 31 Ground 4 R Right directional lights 5 58R Right side parking lights 6 54 Stoplights 7 58L Left side parking lights FITTING INSTRUCTION This towbar is designed to assembly in following cars: OPEL CORSA “D”, 3/5 doors, produced since 2007, catalogue no. E50 and is prepared to tow trailers max total weight 1300 kg and max vertical load 50 kg. From manufacturer Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and right operation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install
[Read the rest of this entry...]

The PCXBV-Ex, -Fx monitors are auto-scanning color monitor with high resolution. These monitors offer the following features:
• Up to 30 display modes, including VESA 85, 1024 x 768, and 1280 x 1024 non-interlaced resolution.
• 85 Hz refresh with 1024 x 768 mode
• Power Management system that exceeds EPA ENERGY STAR™ requirements for saving energy.
• VESA Data Display Channel – DDC1/2B
• Complies with Swedish MPRII and TCO’95 standards for the environment, health and safety
• Anti-glare screen with anti-static coating
[Read the rest of this entry...]

This B&M Short Shift System has been designed to work on most 1993-1998 VW 2.0L 8-valve models. It has been engineered to greatly reduce shift throw and improve shift feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Shift System. Installation of the B&M Short Shift System can be accomplished by anyone with minimal mechanical experience.
[Read the rest of this entry...]

Damaged or defective wires and connectors (e.g. chaffed insulation, broken connector pins, torn crimping) in airbag firing circuits, will cause the airbag light (SRS light) to illuminate, and will set fault code “resistance too high” in airbag control module.
[Read the rest of this entry...]

Preparation
1. Turn off car engine and remove key from ignition
2. Un-mount your radio from the dash in order to get access to the back side of the radio.
Adapter installation
3. Attach square 14 pins connector to the back of the Honda stereo.
4. Find a place where you can place Car2PC. In many cars there is enough room in the dash to place Car2PC.
Note: Make sure you mount Car2PC in a place with enough room so when you mount the car stereo back you do not break the adapter
5. You may use glove box or other spaces in a dash to direct USB+ Audio cables out
[Read the rest of this entry...]

VS123.V2 Tool Set comprises the timing pins and specialised tensioner adjustment tools required for timing belt replacement on all the variants of the Rover 2.0 diesel engine fitted in MG-Rover, Land Rover and Honda models.

FLYWHEEL LOCKING PIN – VS170/1
VS170/1 Locking Pin is used to lock the crankshaft in its timed position. The pin is inserted through a hole in the gearbox mounting back plate and engages a corresponding hole in the flywheel.
[Read the rest of this entry...]