Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Lombardini 11 LD series engines, code 1-5302-296 Workshop Manual

This manual contains the most important information for the repair of LOMBARDINI air cooled, direct injection Diesel engines type 11LD535-3, 11LD625-3 e 11LD626-3.
SAFETY INSTRUCTIONS
•Lombardini Engines are built to supply their performances in a safe and long-lasting way. To obtain these results, it is essential for users to comply with the servicing instructions given in the relative manual along with the safety recommendations listed below.
[Read the rest of this entry...]

Leave a Comment

Volkswagen Wiring Diagram User Manual

Free Download User Manual Volkswagen Wiring Diagram. Explanation: 1. Relay location number, indicates location on relay panel. 2. Arrow, indicates wiring circuit is continued on the previous and/or next page. 3. Connection designation, relay control module on relay panel. Shows the individual terminals in a multi-point connector. 4. Diagram of threaded pin on relay panel, white circle shows a detachable connection. 5. Fuse designation. 6. Reference of wire continuation (current track number).
[Read the rest of this entry...]

Leave a Comment

BMW Wiring Repair Procedure for Firing Circuits of Airbag Systems

Damaged or defective wires and connectors (e.g. chaffed insulation, broken connector pins, torn crimping) in airbag firing circuits, will cause the airbag light (SRS light) to illuminate, and will set fault code “resistance too high” in airbag control module.
[Read the rest of this entry...]

Leave a Comment

9 LD series Engine, code 1-5302-286 Workshop Manual

Every attempt has been made to present within this service manual, accurate and up to date technical information. However, development on the Lombardini series is continuos. Therefore, the information within this manual is subject to change without notice and without obligation. The information contained within this service manual is the sole property of Lombardini. As such, no reproduction or replication in whole or part is allowed without the express written permission of Lombardini.
[Read the rest of this entry...]

Leave a Comment

Ford Mustang Wiring Diagram for 1987-1993 Instrument Cluster

If you are attempting to install a 1990-1993 steering wheel in a 1987-1989 car, then the steering column must also be changed. All
connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug.
[Read the rest of this entry...]

Leave a Comment

BMW E36 with M42 engine Oxygen Sensor Wiring Harness Voluntary Recall Campaign

BMW of North America, Inc. has voluntarily initiated a recall campaign which involves the oxyge sensor wiring harness of the affected vehicles. The potential defect is due to a possible incorrect oxygen sensor harness routing during production. The oxygen sensor harness may have been mistakenly secured with clips to the exhaust heat shield and/or to a bracket on the transmission housing. Due to the movement between the vehicle body, transmission and exhaust system the oxygen sensor harness may stretch and break over time causing the check engine light to illuminate an fault code 70, (oxygen sensor disconnected) to set in the DME.
[Read the rest of this entry...]

Leave a Comment

2002 Mazda Protege 5 Factory Service Manual and Wiring Manuals

THIS MANUAL Range of Topics Service Procedure Symbols Advisory Messages Troubleshooting Procedure Procedures for Use UNITS Conversion to SI Units (Système International d’Unités) Rounding Off Upper and Lower Limits FUNDAMENTAL PROCEDURES Protection of the Vehicle Preparation of Tools and Measuring Equipment Special Service Tools Oil Leakage Inspection Disconnection of the Negative Battery Cable Removal of Parts.
[Read the rest of this entry...]

Leave a Comment

2006 Toyota 4 Runner Wiring Diagram

Part content: ignition coil and igniter, charging system, junction connector, combination meter, engine control, air injection control driver data link connector 3, engine control module. Skid control ECU with actuator suspension, camshaft timing control valve LH, Multiplex Communication System. Engine Immobilisers System.
[Read the rest of this entry...]

Leave a Comment

Super AirFlow Converter II Wiring Diagram by Model

This document describes car models to which the Super Airflow Converter (Product code: 401-A911/401-A913) is applicable, and ECU terminal arrangement drawings. For the operating method and precautions for the Super Airflow Converter, refer to the Instruction Manual. When installing the Super Airflow Converter, both this document and the Instruction Manual are required. Even if the car model and manufacturing year coincide with the contents described in this document, this product may not be installed in certain specification vehicles or remodeled vehicles. The manufacturing years of applicable vehicles are as of January, 2005. For the latest vehicles applications, Please contact your local APEXERA Office or dealer for more information.
[Read the rest of this entry...]

Leave a Comment

A step by step guide to installing the SMT6

This guide focuses on the standard installation of an SMT6 unit. For help with non-standard tuning applications, such as the turbo nitrous control, please refer to the Application Notes. Application Notes can be found under the “Downloads” section on our website www.perfectpower.com.
[Read the rest of this entry...]

Leave a Comment