Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

BMW KM Reseter User Manual

Make mileage correction of BMW E65/E66 CAS by diagnostic socket, BMW E65/E66 new CAS by cluster-plug, BMW E87/E90/E60 CAS by cluster-plug , all versions of BMW LCM by diagnostic socket and BMW EWS by K-line. M35080 and other Eeprom chip in circuit programming. EWS 4.3 (2L86D) programming included.
[Read the rest of this entry...]

Leave a Comment

1988 Mercedes Benz 300CE (124 Chassis) Connecting Test Equipment and Reading Diagnostic Trouble Codes

Testing with the impulse counter should be carried out for rapid fault diagnosis. The
impulse counter output shows only existing faults, since the ACC system does not have
memory capabilities. If one or more faults are indicated, repair as necessary and repeat
the test. Be sure that fuse #7 is good, the battery voltage is between 11-14 volts and the
temperature selector wheel is set to 22°C.
1. Connect the impulse counter to the on-board diagnostic connector.
Black lead of the impulse counter to socket 1
Yellow lead of the impulse counter to socket 7
Red lead of the impulse counter to battery positive terminal.
2. Turn the ignition to the “ON” position.
The LED “U Batt” will be illuminated. If the LED “U BATT” does not illuminate,
check for voltage between socket 1 of the on-board diagnostic connector and
the positive terminal of the battery. If the voltage is not between 11-14 volts,
check for an open circuit or loose ground connection.
Test for voltage between socket 7 and socket 1 of the diagnostic connector.
The voltage should be 6 – 12 volts.
3. Depress the start button for 2 – 4 seconds.
Fault codes will be indicated by the number in the impulse counter display
window. Take note of the impulse display number.
Faults are displayed in ascending order.
The number 1 indicates that no faults are stored in memory.
During the impulse readout, The LED indicator in the fresh air/recirculation
switch will blink.
4. Repeat step 3 until all faults are indicated. After all fault codes have been
displayed, pushing the start button again for 2 – 4 seconds will repeat the fault code
readout sequence.

Source

Leave a Comment

Toyota Echo/Yaris TWM Performance Shifter Cable Bushing Kit Installation Manual

It is preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the shifter cable bushings on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
Estimated Installation Time: 30 minutes
Tools required:
▪ Ratchet
▪ 10 mm deep socket
▪ Ratchet extension
▪ Needle nose pliers/vise grips
[Read the rest of this entry...]

Leave a Comment

Honda Insight Mk1 Grid/Mains IMA Battery Charger

Installation of the charging socket.
Ensure ignition is off and IMA battery switch under the rear cover is in the off position for at least 10 minutes prior to installation. Note the RED switch lock tab has to be removed to allow the IMA battery switch to be moved.
Remove all the IPU compartment cover star drive and 10mm bolts.
Remove the small 8mm black bolt from IMA Main Battery switch area. This is located to the right of the switch when looking in from rear of the vehicle.
[Read the rest of this entry...]

Leave a Comment

VW Golf A5 Variant RHD, 13-pin Electrical Installation Kit

Before starting work read the installation instructions.
The electrical installation kit may only be fitted by qualified specialists.
Follow guidance in the current repair manual when carrying out installation work on the vehicle.
The ABS control unit must be recoded for activation of the trailer stabilisation system.
Caution – disconnect battery
Damage to the vehicle electronics may result in loss of stored electronic data.
Before starting work read out error memory.
[Read the rest of this entry...]

Leave a Comment

A step by step guide to installing the SMT6

This guide focuses on the standard installation of an SMT6 unit. For help with non-standard tuning applications, such as the turbo nitrous control, please refer to the Application Notes. Application Notes can be found under the “Downloads” section on our website www.perfectpower.com.
[Read the rest of this entry...]

Leave a Comment

O2™ : Silicon Graphics 1600SW Flat Panel Monitor Adapter Installation Guide

This guide tells you how to install the Silicon Graphics 1600SW flat panel monitor adapter board in the O2 workstation. There are two classes of O2 workstations, the R5000, and the R10000. The 1600SW flat panel monitor adapter can be installed in either class of O2 workstation.
The guide is organized as follows:
• Chapter 1 describes how to install the adapter board in your O2 workstation.
• Chapter 2 describes how to adjust the flat panel timing tables and how to calibrate color for the 1600SW flat panel monitor.
• Chapter 3 provides troubleshooting information, technical specifications, and regulatory statements.
• The glossary defines many of the terms used in the manual.
[Read the rest of this entry...]

Leave a Comment

BMW Z3 Model 80.v2 Installation Instructions

What’s Included:
1. The Model 80 enclosure bottom
2. The Model 80 vinyl covered enclosure top
3. Alumapro Alusonic 8 subwoofer (optional)
4. Subwoofer grille (optional)
5. Terminal cup
6. Self-adhesive gasket foam
7. Trim cord
8. (8) #10 x ¾” Phillips pan-head screws
9. (4) #14 x 1” hex-head sheet metal screws
10. (4) 1” fender washers
11. (4) 3/8 ” thick rubber washers
12. (12) 1 / 16 ” thick rubber washers
13. (4) #8 x ½” Phillips head machine screws
14. (4) #8 hex nuts
[Read the rest of this entry...]

Leave a Comment

2006+ Honda Civic Si TWM Performance Shifter Base Bushings Installation Manual

Begin the installation by parking on a flat surface, as you will have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
[Read the rest of this entry...]

Leave a Comment

E50-Opel Corsa Towbar Fitting

E50-Opel Corsa D angielska1 2 3 4 5 6 7 8 8 9 9 9 9 10 10 11 11 11 A Plastic elements B Clamp mark in acc. with ISO PN Cables joining 1 L Left directional lights 2 + Rear fog lights 3 31 Ground 4 R Right directional lights 5 58R Right side parking lights 6 54 Stoplights 7 58L Left side parking lights FITTING INSTRUCTION This towbar is designed to assembly in following cars: OPEL CORSA “D”, 3/5 doors, produced since 2007, catalogue no. E50 and is prepared to tow trailers max total weight 1300 kg and max vertical load 50 kg. From manufacturer Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and right operation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install
[Read the rest of this entry...]

Leave a Comment