Free PDF Manual Guide

The BLADE installs easily onto round 1 7/8” to 2” diameter exhaust pipes. Important Notice: In order to install the BLADE, your car must:
• have an exposed, straight tailpipe measuring 1 7/8” – 2.0” in diameter. Example: 2004 Honda Civic
• or, dual exhaust pipes where there are 2 mufflers, each with a single exhaust pipe measuring 1 7/8” – 2.0” in diameter. Example: 2007 Lincoln Town car (in which case 2 BLADES are required).
If your car does not have either of these exhaust configurations, then your exhaust pipe will need modification. This modification is very easy to obtain at any exhaust shop i.e. Meineke, Midas, etc. Simply ask the technician to modify your tailpipe to meet this specification.
[Read the rest of this entry...]

In order to use the Floating Pump to pump water from a dam, swimming pool or large tank into your Silvan spray equipment, simply attatch the 2 ½” BSP fitting on the 64mm lay flat hose supplied, to the 2 ½” BSP outlet of the Floating Pump. Next, either attatch the outlet end of the hose to the inlet of your spray equipment using the camlock fitting supplied, or simply place the outlet of the lay flat hose into the fill opening on the spray equipment. Place the Floating Pump into the dam, swimming pool or tank, ensuring the water is deep enough below the pump inlet to prevent mud etc from being drawn up from the bottom of the dam, swimming pool or tank and into the pump.
[Read the rest of this entry...]

Installation Environment
1) The distance between the unit and outside wall or other goods should be kept over 200mm.The unit should be put in well-ventilated area and its temperature is within -10℃~+40 .℃
2) Check air supply pipeline of the unit and use air source with 3~10 bar to supply for the unit. When connecting the air source, please check if there is leakage in connector for air source and ensure that a certain distance between the air hose and heat source should be kept.
3) To ensure safety. Before connecting the air source, please confirm that the air pressure adjusting valve is closed. Never point the air outlet to personnel.
[Read the rest of this entry...]

This manual covers the oil cooler removing/installing for 1998 cadillac catera engine 3.0L DOHC V6.
Removal 1. Raise and support the vehicle. 2. Drain the engine oil and remove the oil filter housing. 3. Loosen the oil cooler outlet (1) and the inlet (2) lines from engine block. See Fig. 16 . 4. Lower the vehicle. 5. Remove the intake plenum. See INTAKE PLENUM . 6. Remove the intake manifold. See INTAKE MANIFOLD & SPACER . 7. Disconnect the following electrical connectors from the water crossover: The engine coolant [Read the rest of this entry...]

Ripcord for Suction Ventilation
- Will draw away harmful gases and pull in fresh air for the safety of the worker.
- Two units can be used in areas of extremely high concentrations of lethal gases—one on the low manhole, one on the high manhole, and the worker is in the middle manhole.
- When used as a suction ventilator, RIPCORD can provide up to 4130 CFM (cubic feet per minute) of fresh air to work area. SUPER RIPCORD can provide up to 8761 CFM.
[Read the rest of this entry...]

Shopping list from FORD dealer, $15.00 for 2 sets of heater hose o-rings and snap clips, $40.00 heater core, (cheaper at the dealer but no warrantee, aftermarket parts store model preferred by many @ $55) insulated foam tape to wrap new core with (parts dept just gave me what I needed), and a gallon of anti freeze.
[Read the rest of this entry...]

We’ve provided this guide to assist you in connecting your HDTV system. Please follow the directions carefully and get ready to experience HDTV—television you have to see to believe.
Before You Begin
Make sure you have these items:
• HDTV Cable Box
• DTV Remote
• Plastic Wrench
• Component Video Cables
• RCA Cables
• “HDTV Is Only Minutes Away” Card
• Manuals for Cable Box and Remote Control
[Read the rest of this entry...]

Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass through holes on the firewall to prevent fraying. Watches out sharp edges that may damage wires and causes short circuit.
CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete.
[Read the rest of this entry...]

If your air conditioning has stopped working the chances are you have lost most or all or your system refrigerant. The fastest way of finding out is to attempt to have the system refilled by a specialist. They will evacuate any remaining gases and then pressure test the system before refilling. When mine was pressure tested it was immediately obvious that there was a leak somewhere within the condenser matrix situated in front of the engine radiator.
[Read the rest of this entry...]

The components of the K-Jetronic fuel injection system fitted to the 1.8 litre 16V engine are as shown (see illustrations). All procedures are the same as described in Part B of this Chapter except for those given in the following Sections.
2 Idle speed – adjustment
1. Run the engine to normal operating temperature, then check that all electrical components are switched off. Note that the electric cooling fan must not be running during the adjustment procedure.
[Read the rest of this entry...]