Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Guide to R134a Compressor Compatibility

The survivability of a given compressor when retrofitted to R134a has been heatedly discussed for several years. First we need to clarify whether we are discussing a CARQUEST remanufactured compressor or an Original Equipment (OEM) compressor that came with the vehicle. When considering retrofitting to R134a all CARQUEST compressors are up to the task, with the only recommendation being that the GM DA6 be replaced with an HR6 compressor. When it comes to OEM compressors the only guide that should be accepted as true would be the OEM guidelines themselves. GM:
[Read the rest of this entry...]

Leave a Comment

Audi A3 8p RNS-E Retrofit Guide

Detailed on this page are the parts required to fit the RNS-E to Audi A3 8P
The assumption is made that the current system is a single din system

EBay is the best and cheapest source for these units, Dealer price is £2,000+ Needs to have the rounded corners to fit the dash
[Read the rest of this entry...]

Leave a Comment

Audi A3 8p RNS-E Retrofit Guide

RNS-E Installation Instructions and Photo’s A couple words of warning to begin with, if you are paranoid on minor scratches on your interior, please don’t do this. Most likely you will end up with one or a few if you’re not careful Likewise, if you are afraid of applying force when pulling parts out, please don’t do this. Some of the parts are fitted quite tightly, and need a certain amount of force to unplug
[Read the rest of this entry...]

Leave a Comment

1996 Volkswagen Golf A/C-Heater System Manual

COMPRESSOR CLUTCH CONTROL
Evaporator Temperature Switch
Although compressor clutch does not normally cycle on and off, an evaporator temperature switch turns off the compressor clutch if evaporator temperature decreases to 32øF (0øC). This prevents evaporator icing.

A/C Pressure Switch
A/C pressure switch is a triple-pressure switch, which monitors high side pressure. See Fig. 1. If pressure decreases to less than 17.4 psi (1.2 kg/cmý), A/C pressure switch interrupts power to compressor clutch (low-pressure cutout). Switch closes when pressure increases to more than 34.8 psi (2.4 kg/cmý).
[Read the rest of this entry...]

Leave a Comment

Subaru Impreza P1 2000 Workshop Manual

Conduct the tightening procedures by confirming the turning angle of the crankshaft pulley bolt referring to the gauge indicated on the belt cover. Install V-belt air conditioning compressor drive belt tensioner and V-belt cover. cylinder block : check for cracks and damage visually, especially, inspect important parts by means of red lead check. Check the oil passages for clogging.
[Read the rest of this entry...]

Leave a Comment

Batch Monitor User Manual

You can use the Batch Monitor to view or adjust the status of batches and jobs processed by Compressor or Apple Qmaster.You can also use the Batch Monitor to view detailed history for recently completed batches and jobs. You use the Batch Monitor to monitor the transcoding progress of batches and jobs. You can stop, resume, or delete any submitted job or batch up to the point at which the transcoding is complete.
[Read the rest of this entry...]

Leave a Comment

Mitsubishi L300 Engine Inspection Procedure

POWER STEERING OIL PUMP DRIVE BELT TENSION CHECK AND ADJUSTMENT : With your finger tip lightly tap the centre of the belt between the pulleys in the location shown by the arrow in the illustration and then measure the belt vibration frequency. Apply 98N of pressure against the location between the pulleys shown by the arrow in the illustration and then measure the deflection.
[Read the rest of this entry...]

Leave a Comment

99-03 Jetta & 99-03 GTI; 98-05 Beetle Front Kit Installation

I. Preparing the Vehicle
1. Elevate the vehicle (Figure 1) and secure the body with jack stands.
2. Remove the front wheels (Figure 2).
II. Strut Removal
1. Remove left and right sway bar retaining bolts and save for reinstallation (Figure 3).
2. Remove the ABS line retaining clamps from the strut and discard
3. Remove the lower strut mounting bolt and save for later use (Figure 6).
4. Remove the upper strut mounting nut and discard, but retain the upper mounting bracket (Figure 7).
[Read the rest of this entry...]

Leave a Comment

Compact Heat Pump Operation, Installation and Maintenance Manual

Compact Heat Pump Operating Instructions
Prior to use : -
1 Turn off the power supply at the local isolator
2 Open the door, using a coin or similar tool to unlock it
3 Check that the ground pressure gauge reads at least 0.3 bar. If the pressure is lower than this, open the mains cold water supply valve (fitted outside the case) fully until the gauge reads at least 1.8 bar, at which point a “click”will be heard. Close the mains cold water supply valve fully. If you can’t find this valve, or when you open it the gauge reading does not increase, call your installer and ask them about the mains cold water supply valve on the slinky ground array circuit.
[Read the rest of this entry...]

Leave a Comment