Free PDF Manual Guide

How to write cover letter to go along with your CV A good cover letter helps the potential employer decide whether to look at your CV or that of the other candidate. Hence, the cover letter must be crafted carefully with absolutely no spelling or grammar errors. In the cover letter, it is important for you to: • Help the potential employer understand your reasons for sending the resume – Be as specific as possible; if you are looking for
[Read the rest of this entry...]

Introducing your CV—the cover letter What is a cover letter? A cover letter is a letter you send with your CV to a potential employer. It is your opportunity to go beyond the CV and focus the employer’s attention on the experience and skills you possess that are directly related to the position available. A cover letter is basically a sales letter: it promotes your abilities and is written with the potential employer’s interests foremost in mind. Should you write
[Read the rest of this entry...]

It is preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the shifter cable bushings on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent the car from moving while you’re working.
Estimated Installation Time: 30 minutes
Tools required:
▪ Ratchet
▪ 10 mm deep socket
▪ Ratchet extension
▪ Needle nose pliers/vise grips
[Read the rest of this entry...]

1. The filter is located behind the glove compartment. Unscrew the 2 screws at the bottom of the glove box cover to loosen the it. Remove glove box and set it aside.
2. Cut the plastic cover along the dotted lines shown and remove it. Dispose off plastic cover, it is no longer needed. This exposes the metal cross bar under it. Locate and remove 2 additional bolts securing bar. Remove and set it aside.
[Read the rest of this entry...]

DETAILED SET-UP GUIDE
I) BATTERY INSTALLATION
Note: Batteries will fit tightly. To avoid start-up problems make sure that the batteries do not spring free.
A) RAINFALL TRANSMITTER
1. Remove the flat-head screw and battery cover, located on the underside of the base.
2. Observe the correct polarity, and install two AA batteries.
3. Make sure the rubber weather seal is in place and replace the battery cover and screw.
4. Separate the base by turning the rainfall collector in a counter-clockwise direction. Remove the tape from the teeter-totter. Replace the cover.
[Read the rest of this entry...]

One of the biggest performance upgrades you can make to your XR or CRF 50 is to replace the stock semi auto clutch with a fully manual clutch. By adding a manual clutch, you can expect your 50 to launch harder out of corners, and you can also expect to get a faster jump off the starting line. For this “How To” article, we opted to use the proven 3- plate manual clutch kit from Honda Trail Bikes. This kit comes with everything you need except for the clutch lever and perch. With a little time and patience, the Trail Bikes clutch is fairly easy to install and is well worth the effort.
[Read the rest of this entry...]

Getting Started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake. Install rear wheel chocks.
c) If the engine has run with in the past two hours let it cool down.
d) Jack the front of the vehicle and support using properly rated jack stands.
e) Remove the left front wheel.
[Read the rest of this entry...]

■ Install and remove battery
Note: Always switch off the power and disconnect the charger and any other device before removing the cover. Avoid touching electronic components while changing the cover. Always store and use the device with the cover attached.
1. To remove the cover, with the back of the phone facing you. Press and slide the back cover toward the bottom of the phone.
2. To insert the battery, position the battery so the gold-colored contacts match up with those on the phone, and insert the battery into the battery slot.
3. Push down on the other end of the battery to snap the battery into place.
4. Align the back cover with the back of the phone, and slide it toward the top of the phone until you hear a click to lock it into place.
5. To remove the battery, remove cover (see step 1) and insert your finger into the finger grip, to lift the battery from its compartment.
[Read the rest of this entry...]

Preparation Steps for Fuel System Installation
A: Adjust both seats to full forward position with seat backs in full upright position.
B: Disconnect the negative battery cable.
C: Remove the 5 rear interior panels starting with the long piece across the width of the car just beneath the rear glass. Next remove the two flat panels located behind the seats. Next remove the two corner pieces. Lastly, remove the rear center speaker and cover assembly. (The long panel across the width has 3 push lock barbed style securing pins w/one on each end and one in the center) (The 2 flat panels have 4 push lock barbed securing pins each, w/each barb located a couple of inches from each corner of the panels) (The corner sections are held in place with 3 Philips screws which become exposed after the flat panels are removed)
[Read the rest of this entry...]

This manual covers the oil cooler removing/installing for 1998 cadillac catera engine 3.0L DOHC V6.
Removal 1. Raise and support the vehicle. 2. Drain the engine oil and remove the oil filter housing. 3. Loosen the oil cooler outlet (1) and the inlet (2) lines from engine block. See Fig. 16 . 4. Lower the vehicle. 5. Remove the intake plenum. See INTAKE PLENUM . 6. Remove the intake manifold. See INTAKE MANIFOLD & SPACER . 7. Disconnect the following electrical connectors from the water crossover: The engine coolant [Read the rest of this entry...]