Free PDF Manual Guide

This manual covers the oil cooler removing/installing for 1998 cadillac catera engine 3.0L DOHC V6.
Removal 1. Raise and support the vehicle. 2. Drain the engine oil and remove the oil filter housing. 3. Loosen the oil cooler outlet (1) and the inlet (2) lines from engine block. See Fig. 16 . 4. Lower the vehicle. 5. Remove the intake plenum. See INTAKE PLENUM . 6. Remove the intake manifold. See INTAKE MANIFOLD & SPACER . 7. Disconnect the following electrical connectors from the water crossover: The engine coolant [Read the rest of this entry...]

The K&Nо Drycharger included with this kit must be installed on the K&Nо air filter when used with this K&Nо cold air intake system. The K&N cold air intake system a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your cold air intake system to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.
[Read the rest of this entry...]

In this article, you will learn how the camshaft affects engine performance. We’ve got some great animations that show you how different engine layouts, like single overhead cam (SOHC) and double overhead cam (DOHC), really work. And then we’ll go over a few of the neat ways that some cars adjust the camshaft so that it can handle different engine speeds more efficiently.

The key parts of any camshaft are the lobes. As the camshaft spins, the lobes open and close the intake and exhaust valves in time with the motion of the piston. It turns out that there is a direct relationship between the shape of the cam lobes and the way the engine performs in different speed ranges.
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1996-2001 Honda Acura Integra Type R vehicles.
1. Please read through the entire instruction sheet to familiarize yourself with the installation before you begin.
2. Start the engine and check for loose connections or coolant/vacuum leaks, etc.
3. Disconnect the negative battery terminal.
4. Remove the air filter duct, all vacuum hoses, water (coolant) hoses and electrical connectors from the stock throttle body. Mark all hoses and wires to ensure that they are installed correctly on the new throttle body.
Note: Engine coolant may run from the hoses once disconnected. Plug the end of the hose temporarily.
[Read the rest of this entry...]

Hondalogger datalogging is enabled via the addition of a cable and computer chip to the interface board already installed as part of your purchase of the Hondata computer upgrade Stage 2.
Hondalogger software allows you to examine in real time (75-500 readings per second depending on computer) all values from all engine sensors and display an electronic version of the dashboard
[Read the rest of this entry...]

The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet-air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. Because of the increased airflow and reduced inlet temperature, the air-mass flow to the engine increases, this translates to more power.
[Read the rest of this entry...]

Read and understand these instructions BEFORE attempting to install this product.
1) Getting started
a) Make sure vehicle is parked on a level surface.
b) Set parking brake.
c) Make sure you have the anti-theft code for the radio.
d) Disconnect negative battery terminal.
e) If engine has run within the past two hours let it cool down.
[Read the rest of this entry...]

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
[Read the rest of this entry...]

This part is street legal in all 50 states for use on 1994-2001 Acura Integra GSR 1.8L Vtec.
Throttle Body Kit Contents:
1 – Throttle body to manifold gasket
1 – Fast idle thermo valve o-ring with white stripe
1 – Fast idle thermo valve o-ring with red stripe
1 – Fast idle thermo valve o-ring with green stripe
1 – MAP sensor o-ring with blue strip
1 – E.O. # fan shroud decal
[Read the rest of this entry...]

VAUXHALL / OPEL CORSA 1.2, 1.4 Spi 60BHP 1993-99 57-0298 Instruction Sheet A2054-796 Page 1 of 2 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. Note: the kit fits both models. Photo A Photo B 1. Unclip and remove the intake hose from the air box assembly. 2. Remove the air box hot air flap vacuum hose from the rear of the intake housing. Blank off the vacuum outlet pipe with the rubber plug supplied. 3. Unclip and remove the intake scoop from the front cross member and air box assembly. 4. Remove the flexi hose from between the exhaust manifold and the air box hot air flap. 5. Remove the air box assembly from the front mounting rubber, then slide the assembly out of the rear mounting grommets. Remove the assembly from the car. 1. Fit the new mounting bracket to the original rear air box mounting grommet
[Read the rest of this entry...]