Free PDF Manual Guide

The diagram illustrates 8-3/4″ axles. The top is a 66-72 A-body axle. and the other two are longer axles that generally resemble the B and C body and truck axles. C body and truck axles can be shortened and resplined by a quality machine shop, however it is important to note that not all C-body/ Truck axles are created equally.
[Read the rest of this entry...]

The good ol’ Monster rear suspension: single adjustable Boge-Sachs rear shock. It’s gotten a bad rap as an underperformer, but it is still a quality piece with much better adjustment than many other sportbike shocks allow. Then again, why wouldn’t it? It’s a Ducati.
[Read the rest of this entry...]

Everything is included in this kit to add a rear disc brake to your BBR Perimeter Aluminum Frame kit based motorcycle. If you are adapting this kit to the OEM Honda frame or another aftermarket frame kit, you will need our adapter kit PN 550-HXR-5050. Because installation of this kit is beyond the control of BBR Motorsports, Inc, we cannot accept responsibilty for misuse or improper installation. This kit is intended only for use on off-road motorcycles. These instructions are intended only as a supliment to the proper Honda service manual. If the installation of this product is beyond your technical abilities please refer to qualified service personel.

1. Support bike on stand with rear tire off of ground. Remove seat and body work. Remove rear wheel and brake pedal.
2. Remove shipping bracket from master cylinder.
3. Remove shipping wedge from the caliper.
4. Install master cylinder on frame using supplied 6mm bolts.
5. Install master cylinder reservoir on upper subframe bolt using the supplied bracket and longer bolt.
6. Slide caliper (on mount) onto back of swingarm
7. Stick brake hose mounts onto swingarm. Be sure to clean the swingarm to insure that they stick properly.
8. Install rotor and sprocket on the rear hub. BBR recommends using a thread lock adhesive on all these bolts
9. Install rear wheel. Use care to insure that the rotor slides between the brake pads and the wheel spacers stay in place.
10. Install brake pedal tip in desired location. BBR recommends using a thread lock here also.
11. Unsnap the clevis pin from the bottom of the brake reservoir.
12. Install the brake pedal spring on the top bolt mount.

Download

After having replaced the front speakers with the Pioneer TS-131Q, I felt that the rear needed replacing as they are not up to par the aforementioned Pioneers. My choice came down to the Pioneer E-Motion TS-E1376 or TS-E1396, the latter ones being 3-way, having higher frequency response and being more powerful (check these links TS-E1376 and TS-E1396). I was lucky to track them down (through ebay) at a German e–shop, www.caraudio24.de, paid 82 euros (including shipping and Paypal surcharges) and the package arrived in a little more than two weeks. Below are the box contents, 2 speakers, 2 grills, screws and cabling. No instructions however, as these are speakers for universal fitting. Just have a look at them side by side with the OE Renault rear speakers. Absolutely no comments on the magnet size!
[Read the rest of this entry...]

The repair wiring harnesses for E34 touring models are universal for ALL applications (Europe, Japan, US, etc). The part numbers, as noted in other resources like ETK/websites are:
61 10 8 365 702 Right main harness
61 10 8 365 704 Left main harness
61 12 8 355 153 Rear window defroster
63 25 8 359 099 High mount stop light
[Read the rest of this entry...]

Separate the throttle body and insert the mixer in the middle 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch singlepoint position T P S signal is on wire 4 Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections Do not use fast connections OTHER SUGGESTED MATERIAL Pipes and fitting set 54 lt LPG tank tank fixing bracketts for Fiat Tipo NOTES Separer le groupe du monoinjecteur en y installant le melangeur au milieu Sonde lambda 4 fils Signal sur fil noir Positionner le micro switch du L E S sur la position monoinjection Bosch Signal TPS sur fil n 4 Fixer la masse du LES sur le p le negatif de la batterie D [Read the rest of this entry...]

Montare il miscelatore sul corpo farfallato Sonda Lambda a 4 fili Segnale sul filo nero Settare l emulazione del L E S su monoiniettore Bosch Segnale T P S sul filo n C arancio bianco Il filo della spia si trova in centralina sul Pin 9 Con LES 95 non collegare i fili gialli.
[Read the rest of this entry...]

This service campaign includes all 2001 GL1800 Gold Wing models and certain 2002 models. A small percentage of the original equipment rear tires installed on these models could have been damaged during the factory assembly process. As a result, the tire bead may not seal properly against the rim. This condition will allow slightly faster than normal air pressure loss. An under inflated tire may cause abnormal wear patterns and can overheat the tire causing the tread to crack. Normally, tires in good condition may lose one to two psi per month if not checked and adjusted regularly.
[Read the rest of this entry...]

This “how to” assumes you have some basic tools, and safety gear. Safety glasses should be worn at all times when working with tools and automotive fluids. Always use a hydraulic jack and safety stands when lifting or getting under a vehicle. If you are unsure on where to safety lift your vehicle, refer to its owners guide. Brake dust can contain asbestos which has been found to cause cancer. The writer of this how to assumes zero liability in how to use this guide, or any damages that may come from it to you, your property, or others and others property. If you are uncertain at any point, refer to a qualified automotive technician.
[Read the rest of this entry...]

This tutorial will run through the design and simulation of a ‘plain vanilla’ positive edge triggered D flip-flop. Electric allows the design to be done and linked together through what are called facets. These facets are each different hierarchical levels of the design (i.e. Layout, schematic, VHDL, and so on). The design of this flip-flop will be covered in the transistor, schematic, VHDL, and layout levels. The purpose of this tutorial is to cover those topics that are not covered sufficiently in the provided User’s Manual. It is assumed that the student knows how to create a library and facets of that library.
[Read the rest of this entry...]