Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Fiat Brava Bravo 1.4 12V Schematic

Separate the throttle body and insert the mixer in the middle 4 wires Oxigen sensor Signal is on the black wire Switch LES emulation to Bosch singlepoint position T P S signal is on wire 4 Connect L E S ground to the battery negative pole Disconnect the battery before working Soft solder wiring connections Do not use fast connections OTHER SUGGESTED MATERIAL Pipes and fitting set 54 lt LPG tank tank fixing bracketts for Fiat Tipo NOTES Separer le groupe du monoinjecteur en y installant le melangeur au milieu Sonde lambda 4 fils Signal sur fil noir Positionner le micro switch du L E S sur la position monoinjection Bosch Signal TPS sur fil n 4 Fixer la masse du LES sur le p le negatif de la batterie D [Read the rest of this entry...]

Leave a Comment

Fiat Brava Bravo 1.6 Schematic

Montare il miscelatore sul corpo farfallato Sonda Lambda a 4 fili Segnale sul filo nero Settare l emulazione del L E S su monoiniettore Bosch Segnale T P S sul filo n C arancio bianco Il filo della spia si trova in centralina sul Pin 9 Con LES 95 non collegare i fili gialli.
[Read the rest of this entry...]

Leave a Comment

Electric Tutorial

This tutorial will run through the design and simulation of a ‘plain vanilla’ positive edge triggered D flip-flop. Electric allows the design to be done and linked together through what are called facets. These facets are each different hierarchical levels of the design (i.e. Layout, schematic, VHDL, and so on). The design of this flip-flop will be covered in the transistor, schematic, VHDL, and layout levels. The purpose of this tutorial is to cover those topics that are not covered sufficiently in the provided User’s Manual. It is assumed that the student knows how to create a library and facets of that library.
[Read the rest of this entry...]

Leave a Comment

1989 BMW 325i 325is Electrical Troubleshooting Manual

The purpose of this manual is to show electrical schematics in a manner that makes electrical troubleshooting easier. electrical components which work together are shoen together on one schematic. The Wiper washer schematic for example, shows all of the electrical components in one diagram. Schematic troubleshooting : verify the problem, analyze the problem, isolate the problem, repair the problem, check the problem.
[Read the rest of this entry...]

Leave a Comment

/5 FM-1e DUCATI 999R R/C EP MOTORBIKE

Thunder Tiger Corporation guarantees this model kit to be free from defects in both material and workmanship. The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This warranty does not cover any components damaged by use or modification. Part or parts missing from this kit must be reported within 60 days of purchase. No part or parts will be sent under warranty without proof of purchase. To receive part or parts under warranty, the service center must receive a proof of purchase and/or the defective part or parts. Should you find a defective or missing part, contact the authorized Thunder Tiger Service/Distributor nearest you. Under no circumstances can a dealer or distributor accept return of a kit if assembly has started.
[Read the rest of this entry...]

Leave a Comment

Audi A4/A4 Avant Quick reference guide

This quick reference guide gives you a brief introduction to the main features and controls of your vehicle. However, it cannot replace the Owner’s Manual which contains important information and safety warnings. We wish you safe and enjoyable motoring with your Audi.
[Read the rest of this entry...]

Leave a Comment

1971-1977 Mazda RX-2 & RX-3 Clymer Manual Lubrication, Maintenance

This chapter deals with the normal maintenance necessary to keep the Mazda running properly. It includes summaries of service intervals and procedures in table form. Table 1 covers 1971-73 cars; Table 2 covers 1974′s. The recommended service schedules list checks which are easily performed at each stop for gas, and those which are done at specified intervals of miles or time. The last part of the chapter contains a tune-up procedure which simplifies and organizes the process.

ROUTINE CHECKS
The following should he done at each stop for gas.
1. Check engine oil level on the dipstick (Figure 1). Top up to the F mark if necessary, using a grade recommended in Table 3.
2. Check coolant level. The radiator should be full and the expansion tank half full.
NOTE: The coolant level should be checked when the engine is cold. If this isn’t possible, put a rag over the radiator or expansion tank cap when removing to prevent burns.
3. Check the level of the windshield washer tank. It should be kept full.
4. Check sub-zero starting assist fluid (if so equipped). The tank is located above the steering gear box (Figure 2). If necessary, top up with a mixture of 90 per cent ethylene glycol-based anti-freeze and 10 per cent water. Make sure the hose inside the tank is submerged in the fluid. NOTE: // the tank is allowed to become empty, take the car to a dealer for refilling and pump priming.

Download here

Leave a Comment

DUCATI MULTISTRADA 1000DS Owner’s Manual

This function indicates how far the vehicle can travel using the fuel left in the tank. When this display function is not selected, the display automatically switches to “Range” indication as soon as the LOW FUEL LIGHT (10, fig. 5) comes on and the display shows a string of dashes “- – . -” and the indication for 10 seconds. Range indication is then turned on automatically every 60 seconds while the low fuel light stays on. When the vehicle is stopped, either with the engine off or running, the last value stored is displayed until indication is refreshed.
[Read the rest of this entry...]

Leave a Comment

FR 85 / F 70A / F 90A / F140 User Manual

The machine consists of a base plate with a vibration element and an upper part cushioned from the base plate, which is designed as both an engine plate and water tank (F 70A / F 90A). The cushioning between the base plate and the upper part consists of rubber dampers. The power is transmitted from the petrol engine to the vibration element via a V-beltwhich can be adjusted with a belt tensioner. The engine V-belt pulley is fitted with an integrated centrifugal clutch, which allows the engine to be started and run idle without the vibrator being connected.
[Read the rest of this entry...]

Leave a Comment

Kawasaki Teryx 750 ATV Clutch Kit Instructions

The instructions we provide are guidelines only and will not thoroughly explain how to set up a racing vehicle. Claims of performance gains, durability, etc. are based on the experience of TEAM Industries and others and do not constitute a guarantee of similar performance in every application. We believe that the contents and specifications within this set of instructions are correct. We assume no liability for any errors in model applications. We reserve the right to change specifications, product descriptions, product quality and application at any time without notice.
[Read the rest of this entry...]

Leave a Comment