Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

2002 Mazda Protege 5 Factory Service Manual and Wiring Manuals

THIS MANUAL Range of Topics Service Procedure Symbols Advisory Messages Troubleshooting Procedure Procedures for Use UNITS Conversion to SI Units (Système International d’Unités) Rounding Off Upper and Lower Limits FUNDAMENTAL PROCEDURES Protection of the Vehicle Preparation of Tools and Measuring Equipment Special Service Tools Oil Leakage Inspection Disconnection of the Negative Battery Cable Removal of Parts.
[Read the rest of this entry...]

Leave a Comment

Mazda RX-2 / RX-3 Clymer Manual Chapter 9 Transmission

The RX-2 and RX-3 are available in the United Stales with a 4-speed manual transmission or a 3-speed automatic. This chapter contains removal and repair procedures for the manual transmission, as well as testing and adjustment procedures for the automatic. Specifications are given in Table 1 (end of chapter).
MANUAL TRANSMISSION
The manual transmission consists of clutch housing, transmission case, and rear extension. Figure 1 (next page) shows the case and rear extension. Figure 2 (page 155) shows the shifting mechanism.
[Read the rest of this entry...]

Leave a Comment

2004 Mazda Mazda RX-8 Quick Tips

RX-8 Quick Tipsо are designed to quickly familiarize you with some important features of your RX-8 This Driver’s View tab is your index to the Quick Tipsо, locate the item you would like to learn more about and then turn to the listed tab Be sure to see the tab called Getting Started, this section contains important operating tips about your RX-8 Items identified with a Rotary Engine symbol call out important information.
[Read the rest of this entry...]

Leave a Comment

BMW E36 with M42 engine Oxygen Sensor Wiring Harness Voluntary Recall Campaign

BMW of North America, Inc. has voluntarily initiated a recall campaign which involves the oxyge sensor wiring harness of the affected vehicles. The potential defect is due to a possible incorrect oxygen sensor harness routing during production. The oxygen sensor harness may have been mistakenly secured with clips to the exhaust heat shield and/or to a bracket on the transmission housing. Due to the movement between the vehicle body, transmission and exhaust system the oxygen sensor harness may stretch and break over time causing the check engine light to illuminate an fault code 70, (oxygen sensor disconnected) to set in the DME.
[Read the rest of this entry...]

Leave a Comment

TPMS Sensor Service Guidelines

This document outlines the guidelines for the manual mounting on the rim of EnTire/TRW fixed angle TPM sensors.
This document does not cover any other TPM sensors.
- Sensor & valve components
- Step 1 Start fitting the valve unit on the rim
- Step 2 Tighten the nut
- Step 3 Check the assembly sensor – valve – rim
[Read the rest of this entry...]

Leave a Comment

1993-95 Mazda RX-7 PowerMax Turbo System Installation Manual

Thank you for purchasing the XS Engineering PowerMax System for the 1993-95 Mazda RX-7 (FD3S). This system has been designed by XS Engineering’s Research and Development Team to complement the RX-7’s sturdy yet agile chassis by adding a healthy dose of raw turbocharged power! By taking advantage of Mazda’s potent 1.3-liter 13B-REW rotary engine, XS Engineering bends the laws of physics once again by designing a single turbo system that delivers both immediate boost response and 368 Dynojet-proven horsepower to the wheels at only 13.5psi! Aside from this, please take the time to read through and understand this manual fully before you proceed with the installation process.
[Read the rest of this entry...]

Leave a Comment

OPEL Zafira Engine transmission Installation instruction

Installation instructionZF Trading GmbH Obere Weiden 12 97424 Schweinfurt Germany © by ZF Trading GmbH 0032004_OSOPE019 OPEL Zafira Engine transmission Removing and fitting/replacing manual transmission. Remove: Lift vehicle. Remove lower engine cover. Dismount front exhaust tube Remove catalytic converter. Dismount central silencer. Remove water tank cover. Remove water tank insulation. (see Fig.1) Align engine/gearbox unit by means of holding devices. Remove front axle body Have steering wheel engage in straight position. Unscrew clamping joint. Detach intermediate spindle. (see Fig.2) Remove battery. Remove battery holder. Vehicles with petrol engine Disconnect lambda sensor connector. (see Fig.3) Secure radiator against falling down by Fig. 2 1 Clamping joint. Fig. 3 1 Lambda sensor connector. Fig. 4 1 Wire. No. Special tool Parts number Footnote Engine transmission 1 Engine support MKM-833-1 2 Adapter plate. MKM-883-2 3 Holding device(s) KM-909-B 4 Holding device(s) KM-6001-A Clutch 1 Blocking tool KM-652 2 Centering mandrel KM-734 F17 gearbox 3
[Read the rest of this entry...]

Leave a Comment

Force-Directed Approaches to Sensor Localization

Force-Directed Approaches to Sensor Localization ALON EFRAT, DAVID FORRESTER, ANAND IYER, and STEPHEN G. KOBOUROV University of Arizona CESIM ERTEN Kadir Has University OZAN KILIC Isik University As the number of application areas where sensor networks are used increases, the sensor network localization problem gains more importance. It is the problem of recovering the correct position of each node in a network of sensors from partial connectivity information such as adjacency, range, or angle between neighboring nodes. In this paper,
[Read the rest of this entry...]

Leave a Comment

Sensor Deployment and Target Localization Based on Virtual Forces

Sensor Deployment and Target Localization Based on Virtual ForcesSensor Deployment and Target Localization Based on Virtual Forces Yi Zou and Krishnendu Chakrabarty Abstract— The effectiveness of cluster-based distributed sensor networks depends to a large extent on the coverage provided by the sensor deployment. We propose a virtual force algorithm (VFA) as a sensor deployment strategy to enhance the coverage after an initial random placement of sensors. For a given number of sensors, the VFA algorithm attempts to maximize the sensor field coverage. A judicious combination of attractive and
[Read the rest of this entry...]

Leave a Comment

AX15 5 Speed Transmission Retro-Fit For The AX5 4 Cyl. 5 Speed Ext. Slave

This kit is designed to fit the 1995 and newer AX15 transmission. Earlier model transmissions can use a stock pilot bushing, one with a .590″ I.D. We recommend that the stock flywheel be removed and resurfaced at a machine shop. A new clutch disc and release bearing has been provided in this kit. A new pressure plate is also recommended before installing your new transmission. We offer a Centerforce pressure plate, Part No. CF361914. Before disposing of the old AX5 transmission, you will need to retain the shifter housing from that transmission. You will also be using the stock 4 cylinder bellhousing and stock release arm and crossmember mount.
[Read the rest of this entry...]

Leave a Comment