Free PDF Manual Guide

User Manuals – Owners Manual – User Guide

Acura GSR Whirlwind Intake Manifold Instructions

Removal
1. Relieve the fuel pressure in the system by loosening the banjo bolt on the top of the fuel filter. Disconnect the fuel line from the fuel rail. It is a good idea to replace the washers. Disconnect the fuel harness holder and unbolt. Disconnect the hoses from the fuel pressure regulator (FPR).
2. Disconnect intake hose/pipe from throttle body. Disconnect all hoses leading to the throttle body and intake manifold. Disconnect throttle cable bracket on manifold and throttle cable from throttle body. Disconnect the cables to the the throttle position sensor (TPS) and the map sensor on the throttle body.
3. Unbolt two lower intake manifold bolts that secure manifold to engine block. This bracket willl still be used to accommodate the heater bypass pipe. Unbolt manifold from engine block. Remove manifold, throttle body, and fuel rail as one unit.
4. Remove the intake air bypass (IAB) vacuum tank, check valve and control solenoid unit. Due to the different design of your new manifold, these parts will no longer be used. Do not remove the FPR hose. This hose will be used in the re-installation process.
[Read the rest of this entry...]

Leave a Comment

VAUXHALL / OPEL CORSA Installation Instruction Sheet

Installation Instruction Sheet - VAUXHALL / OPEL CORSA 1.2, 1.4 ...VAUXHALL / OPEL CORSA 1.2, 1.4 Spi 60BHP 1993-99 57-0298 Instruction Sheet A2054-796 Page 1 of 2 PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE FITTING THE KIT. Note: the kit fits both models. Photo A Photo B 1. Unclip and remove the intake hose from the air box assembly. 2. Remove the air box hot air flap vacuum hose from the rear of the intake housing. Blank off the vacuum outlet pipe with the rubber plug supplied. 3. Unclip and remove the intake scoop from the front cross member and air box assembly. 4. Remove the flexi hose from between the exhaust manifold and the air box hot air flap. 5. Remove the air box assembly from the front mounting rubber, then slide the assembly out of the rear mounting grommets. Remove the assembly from the car. 1. Fit the new mounting bracket to the original rear air box mounting grommet
[Read the rest of this entry...]

Leave a Comment

E50-Opel Corsa Towbar Fitting

E50-Opel Corsa D angielska1 2 3 4 5 6 7 8 8 9 9 9 9 10 10 11 11 11 A Plastic elements B Clamp mark in acc. with ISO PN Cables joining 1 L Left directional lights 2 + Rear fog lights 3 31 Ground 4 R Right directional lights 5 58R Right side parking lights 6 54 Stoplights 7 58L Left side parking lights FITTING INSTRUCTION This towbar is designed to assembly in following cars: OPEL CORSA “D”, 3/5 doors, produced since 2007, catalogue no. E50 and is prepared to tow trailers max total weight 1300 kg and max vertical load 50 kg. From manufacturer Thank you for buying our product. Their reliability has been confirmed in many tests. Reliability of towbar depends also on correct assembly and right operation. For this reasons we kindly ask to read carefully this instruction and apply to hints. The towbar should be install
[Read the rest of this entry...]

Leave a Comment

1999.5 – 2005 Volkswagen Golf/GTI 2.0L 4 Cyl. Cold Air System Installation

Installing the AEM Cold Air System
a) When installing the AEM intake, DO NOT completely tighten the hose clamps, MAF sensor assembly or the mounting tab hardware until instructed to do so later in these instructions.
b) Install the rubber mount in the outermost (towards driver’s side of vehicle) hole to the rear of the large opening behind the headlight. Insert the rubber mount from below (Fig. 16) and secure it with a large fender washer and lock nut from the top. (Fig. 17)
c) Place a large fender washer on the stud that originally secured the lower intake tube in place. (Fig. 18)
d) Re-install the MAF sensor into the plastic intake hose, rotating the electrical connector to the original position. Use the original spring hose clamp. Note: it is possible to install the MAF sensor backwards. DO NOT INSTALL BACKWARDS. Make sure that the end with the flange (originally in the airbox) is still facing away from the throttle body. If you are still unsure, there is an arrow with the word “flow” molded into the MAF sensor body. (Fig. 19)
[Read the rest of this entry...]

Leave a Comment

Forge Motorsport Golf 1.8T, SEAT Leon 1.8T and Audi A3 1.8T DV fitting guide

Tools required: – Cross head screwdriver, Flat blade screwdriver, 6mm and 7mm hose
clip drivers, Sharp craft knife.
1/ Open bonnet/hood. Remove the plastic engine cover. Remove the hose running between the throttle body housing and the top intercooler connection (bottom left hand corner of the picture above)
2/ Fit the new hose with the 25mm spout as shown above. If the hose is too long it will probably become misshapen, if this happens then remove and simply trim the ends with a sharp craft knife, only remove 10-15mm at any time and refit to check the hose shape after each cut if required. Once happy with the fit then secure with the hose clips supplied.
[Read the rest of this entry...]

Leave a Comment

Ford ACCEL Digital Fuel Injection Engine Management System Installation Manual

ACCEL recommends using a 180 degree thermostat in most applications. Place your thermostat and gasket onto your manifold, put your thermostat housing onto the manifold and bolt in place. When installing your fuel injectors, be careful not to cut the O-Rings. A small amount of oil on each O-Ring will aid in the assembly. Please reference a service manual for proper torque sequence and vacuum line routing.
[Read the rest of this entry...]

Leave a Comment

1998 Cadillac Catera Engine 3.0L Oil Cooler

This manual covers the oil cooler removing/installing for 1998 cadillac catera engine 3.0L DOHC V6.
Removal 1. Raise and support the vehicle. 2. Drain the engine oil and remove the oil filter housing. 3. Loosen the oil cooler outlet (1) and the inlet (2) lines from engine block. See Fig. 16 . 4. Lower the vehicle. 5. Remove the intake plenum. See INTAKE PLENUM . 6. Remove the intake manifold. See INTAKE MANIFOLD & SPACER . 7. Disconnect the following electrical connectors from the water crossover: The engine coolant [Read the rest of this entry...]

Leave a Comment

1996-2001 Honda Acura Integra Type R Edelbrock 65mm Throttle Body INSTALLATION INSTRUCTIONS

This part is street legal in all 50 states for use on 1996-2001 Honda Acura Integra Type R vehicles.
1. Please read through the entire instruction sheet to familiarize yourself with the installation before you begin.
2. Start the engine and check for loose connections or coolant/vacuum leaks, etc.
3. Disconnect the negative battery terminal.
4. Remove the air filter duct, all vacuum hoses, water (coolant) hoses and electrical connectors from the stock throttle body. Mark all hoses and wires to ensure that they are installed correctly on the new throttle body.
Note: Engine coolant may run from the hoses once disconnected. Plug the end of the hose temporarily.
[Read the rest of this entry...]

Leave a Comment

1992–1995 Honda Civic Cold Air System Installation Instructions

The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot underhood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation.
[Read the rest of this entry...]

Leave a Comment

Acura Integra GSR VTEC Throttle Body Installation Instruction

This part is street legal in all 50 states for use on 1994-2001 Acura Integra GSR 1.8L Vtec.
Throttle Body Kit Contents:
1 – Throttle body to manifold gasket
1 – Fast idle thermo valve o-ring with white stripe
1 – Fast idle thermo valve o-ring with red stripe
1 – Fast idle thermo valve o-ring with green stripe
1 – MAP sensor o-ring with blue strip
1 – E.O. # fan shroud decal
[Read the rest of this entry...]

Leave a Comment