Free PDF Manual Guide

Front door trim, removing and installing
1 – Door trim
Remove screw cap – 5 -
Remove screw – 4 – (1x).
Unclip inner and outer connecting pieces. .
Lift door trim about 20 cm upward and remove from door.
Detach release cable for interior door handle
Disconnect electrical connectors
Clip locators – 3 – (7x) must be clipped in place when installing door trim.
[Read the rest of this entry...]

This Dash Mount is designed for: Location: Tools Required: Monteringsanvisning Mounting Instruction Do not use force when working with plastic components. Use extreme care not to scratch the interior of the vehicle. MTU may not be held liable for any damage to a vehicle connected to the installation. Correct direction of the rose pattern. Steg 1: Vipp av den ytre rammen med luftedyser midt på dashbordet. Steg 2: Tre Dash Mounten inn på rammen. Plasse- ring kan justeres etter ønske. Steg 3: Press rammen med dyser på plass igjen. On the center air vent. Flat bending tool Step 1: Tilt out the outside frame and air vent. in the middle of the dashboard. Step 2: Tread the Dash Mount on the frame. You can choose the position as you wish. Step 3: Press the frame back into position. Opel Vectra A ………………….. 1989-1995 …………… 2 x Airbag Opel Calibra …………………….
[Read the rest of this entry...]

1. Removal of the original bumper:
Remove all screws which hold the bumper. Also remove the screws which hold the alloy bar and remove the bumper with the alloy bar. Remove the alloy bar from the bumper and install it into the new Hofele-Design bumper.
2. Placement of the Hofele-Design front bumper on the car:
Place the new bumper on the car but do not yet bolt it on.
[Read the rest of this entry...]

1) Disconnect negative battery cable and ground strap at transaxle. Disconnect positive battery cable. Remove battery and battery base. Remove drain plug, and drain transaxle fluid (remove fill plug to speed draining). Install drain plug with NEW washer, and tighten plug to specification. See TORQUE SPECIFICATIONS TABLE at the end of this article.
2) Disconnect wiring for starter motor, transaxle lock-up control solenoid and shift control solenoid. Remove starter. Disconnect mainshaft and countershaft speed sensor connectors. Remove complete air cleaner case assembly. Disconnect and remove throttle control cable at transaxle bracket.
[Read the rest of this entry...]

I. Preparing the Vehicle
1. Elevate the vehicle (Figure 1) and secure the body with jack stands.
2. Remove the front wheels (Figure 2).
II. Strut Removal
1. Remove left and right sway bar retaining bolts and save for reinstallation (Figure 3).
2. Remove the ABS line retaining clamps from the strut and discard
3. Remove the lower strut mounting bolt and save for later use (Figure 6).
4. Remove the upper strut mounting nut and discard, but retain the upper mounting bracket (Figure 7).
[Read the rest of this entry...]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”

NOTE:
• Be careful not to damage the body paint finish.
• This trunk spoiler kit should be installed only if the ambient air temperature is 60°F (15°C) or above.
• Wash and wax the area to be covered. Use a
high-quality paste wax.
[Read the rest of this entry...]

Most 18” wheels will clear the outer diameter of the caliper on a 355mm kit. However, the more critical clearance is the gap between the spokes of the wheel and the face of the caliper. Do not assume that a 19”, 20” or even 24” wheel will clear the face of the caliper. The actual metal-to-metal distance measured from the stock rotor face to the inside of the wheel spokes is 62.25mm for the BMW X5 front kit. StopTech recommends at least 2mm of additional clearance. See the Wheel Fitment Drawing page on the StopTech website for more specific measurements, at www.stoptech.com. Note: Final fitment of the wheel to the caliper is the responsibility of the customer.
[Read the rest of this entry...]

Part content: ignition coil and igniter, charging system, junction connector, combination meter, engine control, air injection control driver data link connector 3, engine control module. Skid control ECU with actuator suspension, camshaft timing control valve LH, Multiplex Communication System. Engine Immobilisers System.
[Read the rest of this entry...]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.

NOTE:
• Be careful not to damage the body paint finish.
• Body side moldings should only be installed if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
• These installation instructions show the left body side moldings being installed. The same procedure applies to installing the right body side moldings.

1. Using one alcohol swab, clean the area where the left body side molding will attach.
2. Align the front template to the left front door and attach the template to the door using strips of masking tape.
3. Place the left front body side molding against the template to verify the installation position on the left front door. Remove the body side molding.
4. Peel back approximately 1½ to 2 inches of adhesive backing from each adhesive tape, and tape the ends to the front surface of the body side molding. Remove the small end pieces of the adhesive backing.
5. Align the left front body side molding with the front template, and attach it to the left front door. If the vehicle has door edge film installed, align the end with the door edge film.

Download

This “how to” assumes you have some basic tools, and safety gear. Safety glasses should be worn at all times when working with tools and automotive fluids. Always use a hydraulic jack and safety stands when lifting or getting under a vehicle. If you are unsure on where to safety lift your vehicle, refer to its owners guide. Brake dust can contain asbestos which has been found to cause cancer. The writer of this how to assumes zero liability in how to use this guide, or any damages that may come from it to you, your property, or others and others property. If you are uncertain at any point, refer to a qualified automotive technician.
[Read the rest of this entry...]