Free PDF Manual Guide

Your new EmerGen Switch will provide you with a way to safely utilize your generator power through your existing electrical wiring during a power outage. You’ll install your switch next to your home’s electrical panel load center and then you’ll connect circuit breaker wires to the transfer switch’s circuits. Once you power up your portable generator, you will manually turn on each switch and that generator energy is transferred as electrical power and goes through the house circuits you have previously chosen. Your EmerGen Switch is easy for a licensed electrician or qualified professional to install, safe for a homeowner to operate, and will work with 120/240V single phase AC generators, factory equipped with NEMA type receptacles L14-20R or L14-30R , depending on the size EmerGen Switch you have chosen. Your EmerGen Switch cannot permit connection to both utility and generator power at the same time.
[Read the rest of this entry...]

Step 1 – Place the grille inside the opening. The grille should conform to the center opening on the car and fit snugly. This will actually provide the support for the grille.
Step 2 – Use a pencil or magic marker to mark the holes where you want to route the zip ties. On the center grille, the cable ties will attach to the plastic OEM grille slats.
Step 3 – Route a zip tie through an opening in the grille (from the back) and then through the front of the grille via an adjacent hole. Unless you have tiny hands, you may need to attach a second zip tie to the end of the first to add length.
[Read the rest of this entry...]

New Bracket installation:
- install new license plate (and frame, if any) BEFORE installing taillight on bracket
- pass wires on the wide cateye taillight through main bracket, and fasten taillight on the bracket using two bolts on the light; make sure to install the light so that clear window faces downward, toward lic. plate
- install new bracket over metal fender frame as shown; loosely fasten one side tab, press bracket over other side, and fasten the other tab, and tighten bolts evenly.
- re-install wires through clips in fender frame; make sure wiring is properly routed, to avoid interference with rear wheel, fender bolts, etc.
- re-install fender assembly; used specified Torque values (47 ft. lb; per service manual)
- reconnect rear turn signal wires (brakelight connection – see below)
[Read the rest of this entry...]

The MR4 (Black) and MR4W (White) are a compact two-way speaker system designed for constant-impedance systems. The 5″ carbon fiber woofer mounted on a 120° x 100° constant-directivity horn, in combination with a 0.5″ mylar dome tweeter, provide natural, smooth sound reproduction, ideal for use in business music systems and indoor/outdoor background music applications. The passive crossover is designed to reduce heat dissipation and optimize the power response of the loudspeaker.
[Read the rest of this entry...]

Thank you for purchasing our Auxiliary Input Adapter for Mercedes Benz D2B fiber equipped vehicles (AUX-IND2B). This interface is designed to provide a quality sound input to your car’s stereo system. Most frequently our customers use this for iPod or satellite radio. Below is a list of components and tools that you will need. Some you should have received or may have purchased separately.
[Read the rest of this entry...]

If you are attempting to install a 1990-1993 steering wheel in a 1987-1989 car, then the steering column must also be changed. All
connections will hook up in the steering column except for the harness from the steering wheel, which provides the horn and cruise control signal. The windshield wipers will not work if the 1990-1993 switch is used on the 1987-1989 harness. Testing with a multimeter will show you the wires that Ford chose to move when the design of the switch changes. All controls have the same wiring except the windshield wipers. After the correct wires are determined, it is an easy task to remove the wires from the plug by pressing down on the tab on the front of the plug and sliding the wire out the back. Then, the wire can be inserted into the previously unused connection hole on the plug.
[Read the rest of this entry...]

Step 1:Take the ignition cover off. Are The Replacement Parts Similar? Compare the replacement part to the original. The replacement part should match, including the mounting hole locations. If not: Double check the application listing with your bike.
Step 2: Remove the flywheel using a proper puller. Remove the baseplate with the original stator. Disconnect the wires from the wiring loom.
Step 3: Remove existing stator coil off the baseplate and cut the wires close to the coil. Replace it with the new unit and feed the new leads though the holes in the baseplate.
[Read the rest of this entry...]

The GROM AUX adapter is designed to provide endless hours of listening pleasure through most vehicles factory radio. To insure that your AUX interface performs correctly in your car or truck, we recommend that you read this entire manual before attempting install the GROM interface.

Proper mounting location
Securely install the interface in a location free from; heat, humidity, moving parts or direct sunlight. Beware of hot-air flow from your vehicle’s climate control system. We recommend securing the interface to a suitable location, free of sharp metal edges, using double sided tape, Velcro or wire ties.
[Read the rest of this entry...]

Montare il miscelatore sul corpo farfallato Sonda Lambda a 4 fili Segnale sul filo nero Settare l emulazione del L E S su monoiniettore Bosch Segnale T P S sul filo n C arancio bianco Il filo della spia si trova in centralina sul Pin 9 Con LES 95 non collegare i fili gialli.
[Read the rest of this entry...]

1. Mounting the Air / Fuel Meter
Using the supplied Velcro, Suction Cups or L-Brackets, locate the Air /Fuel Meter in a convenient location that does not obstruct your view.
TIP: Clean the mounting area with alcohol or another nonabrasive cleaner to ensure the Velcro or Suction Cups adhere properly.
2. Disconnect the Negative Battery Cable
Locate the battery and remove the negative battery cable.
[Read the rest of this entry...]